Tabla de contenido
IMPORTANT
Please read
these
instructions carefully before you start to assemble this product.
Please
carry
out the
steps
in
the order
set
out
in
these instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
Safetv advicc
For
safety purposes we
strongly recommend the product to
be
assembled by at
least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components.
Always wear gloves,
eye
protection,
and long sleeves when assembling or
performing
any maintenance on
your product.
Do
not attempt to
assemble the
product
in
windy
or
wet conditions.
Do
not attempt to
assemble the
product if
you are
tired,
have
taken drugs,
medications or alcohol,
or
if
you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder
or
power tools,
make sure
that
you
are
following
the
manufacturer's safety advice.
Do
not climb
or stand on
the
roof.
Do
not
hang or
lay on
the profiles.
Heavy
articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy
snow load
on
the roof
can
make
it
unsafe
to
stand below or nearby.
If
color
was scratched
during
assembly it
can be
fixed.
Cleaning instruction:.
In
order to
clean
the product,
use
a
mild detergent solution
and rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product
once assembly
is
complete.
Before Assembly
Choose
your
site
carefully before beginning assembly.
The
ground
surface must
be
perfectly flat
and leveled and have
a
solid
base such
as
concrete, asphalt, deck
etc.
Sort the parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep all small
parts
(screws etc.) in
a
bowl
so
they
do
not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to
constructing the product.
Attention
Please
make sure you install
the
panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT") and remove
the sticker
as
panels
are in
place.
During Assembly
When
encountering the information
icon, please refer
to the relevant
assembly step for
additional comments
and assistance.
During assembly
use
a
soft surface below the parts to avoid scratches
and damages.
Steps
Step 8a: Carefully
spread silicone along the cross-section
of
the profile and
immediately attach the profiles together.
It
is
recommended to wipe the extra
residue silicone.
Step
10: It
is
recommended to
use
a
carton or other soft material under the
lowered corner
in
order to avoid scratches and peeling of paint.
*This note also refers
to step
18
Steps 13+14:
Optional
-
if
you wish to add
Palram's
Curtains or Netting
Set,
(Palram's
Curtains
/
Netting
Set are
not supplied).
It
is
not
possible to add the clips at
a
later time, once the
product
is
fully
assembled.
Steps
19+21:
Please
note
that
screws
insertion should
be
done from the outside.
Step 23b:
Please
add silicone
on
the inner
area
of part #8327
as
illustrated.
Step 24:
Please use
dry cloth to wipe the
panel
prior to attaching the
sealing
tape to the panels' edges.
Step 29a:
Please
drill
holes
in
the
panels
to
be
located precisely parallel to the
holes
in
the gutters' profiles.
Step 30:
Please
level
the profile's
legs
and
adapt
screws and plugs to
your
specific ground type.
* Please
tighten
all screws
when completing assembly.
Note:
Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
Tabla de contenido
