General Safety Instructions; Description Of The Controls; Instruction Manual - AEG MC 4402 Instrucciones De Servicio

General safety instructions

To avoid the risk of fi re or an electric shock, you should
not expose the device to rain or moisture. Consequently,
do not use the device in the immediate vicinity of water
- for example near a bath tub, a swimming pool or in a
damp cellar.
Use the device only for the intended purpose.
Only connect the device at a properly installed plug
socket. Pay attention that the specifi ed voltage corres-
ponds to the voltage of the plug socket.
When using external mains supply, pay attention to the
correct polarity and voltage. Always place the batteries
in the correct direction.
Assemble the device in such a way that the available
ventilation openings are not covered.
Never open the housing of the device. Incorrect repairs
can constitute a considerable risk for the user. Should
the device become damaged, in particular the mains
supply cable, do not operate the device any longer, but
rather have it repaired by an expert. Check the mains
supply cable regularly for damage.
For safety reasons a broken or damaged mains lead may
only be replaced by an equivalent lead from the manuf-
acturer, our customer service department or a similary
qualifi ed person.
If the device is not used for a longer period, remove the
plug connector from the plug socket or take out the
batteries.
These symbols may be found on the machine and are
intended to indicate the following:
The lightning symbol should advise the user
of parts in the inside of the device which carry
dangerously high voltage levels.
The symbol with an exclamation mark should
advise the user of important operation or
maintenance instructions in the accompa-
nying documentation.
Devices bearing this symbol work with a
„class 1 laser" for tracing the CD. The built-in
safety switches should prevent the user being
exposed to dangerous laser light, which is
invisible to the human eye, when the CD compartment
is opened.
Under no circumstances should these safety switches
be bypassed or manipulated, as this could result in a
danger of exposure to the laser light.
34
5....-05-MC 4402 AEG 34

Description of the Controls

1 Sensor for the remote control
2 STANDBY/ON button
3 I CD button (reverse search)
4 Function selection switch CD
5 I CD button (forward search)
6 Function selection switch TAPE
7 MEMORY button
8 CD compartment
9 LED display/frequency scale
10 OPEN/CLOSE CD compartment
11 / II CD play/pause button
12 Function selector switch BAND/TUNER
13 CD stop button
14 Function selection switch TONE
15 CD REPEAT button
16 VOLUME control
17 Cassette compartment
18 door PUSH OPEN
19 Function buttons - cassette
a II pause button - cassette
b / stop/eject button - cassette
c forward wind button - cassette
d reverse wind button - cassette
e play button - cassette
b record button - cassette
f
Reverse Side
20 FM throw-out aerial
21 AM aerial connection
22 PHONES headphone connection
23 SPEAKER R/L - loudspeaker connections
24 Mains connection
Remote Control
25 TAPE button
26 TUNER / BAND button
27 DISPLAY button
28 MP3 MOD(US) button
29 - VOLUME - button
30 / II CD play/pause button
31 I CD button (reverse search)
32 TONE button
33 MEMORY button
34 REPEAT button
35 MUTE button
36 I CD button (reverse search)
37 CD stop button
38 + VOLUME - button
39 ESP button
40 INTRO button
41 RANDOM button
42 CD button
43 POWER button
Initial Operation of the Machine/
Introduction
• Please read the instructions carefully before using the
machine for the fi rst time!
• Remove any transport screws on the CD and casset-
te sections.
• Select a suitable place to install the machine and
loudspeakers, e.g. a dry, fl at, non-slip surface on
which the device is easy to operate.
• Please ensure that the device is suffi ciently ventila-
ted!
01.03.2004, 12:30:35 Uhr