Before Starting The Engine - Husqvarna LT1597 Manual De Operario

Ocultar thumbs Ver también para LT1597:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

TO OPERATE ON HILLS
CAUTION: Do not drive up or down hills
with slopes great er than 15° and do not
drive across any slope.
Choose the slowest speed before starting up or down
hills.
Avoid stopping or changing speed on hills.
If slowing is necessary, move throttle control lever to
slower position.
If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
Move gearshift lever to 1st gear. Be sure you have
allowed room for tractor to roll slightly as you restart
movement.
To restart movement, slowly release parking brake and
clutch/brake pedal.
Make all turns slowly.
REVERSE OPERATION SYSTEM (ROS)
(See Fig. 14)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse
direction with the attachment clutch engaged will shut off the
engine unless ignition key is placed in the ROS "ON" position.
WARNING: Backing up with the attachment clutch en-
gaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.
USING THE REVERSE OPERATION SYSTEM
Only use if you are certain no children or other bystanders
will enter the mowing area.
Depress clutch/brake pedal all the way down and hold.
With engine running, turn ignition key counterclockwise
to ROS "ON" position.
Look down and behind before backing.
Move gear shift lever to reverse (R) po si tion and slowly
release clutch/brake pedal to start movement.
When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
ROS "ON"
POSITION
OPERATION
ENGINE "ON" POSITION
(NORMAL OPERATING)
Fig. 14
TO TRANSPORT
Raise attachment lift to highest position with at tach ment
lift control.
When pushing or towing your tractor, ensure gearshift
lever is in neutral (N) position.
Do not push or tow tractor at more than five (5) mph
(8 km/h).
NOTE: To protect hood from damage when transporting
your tractor on a truck or a trailer, ensure hood is closed
and secured to tractor. Use an appropriate means of tying
hood to tractor (rope, cord, etc.).
TOWING CARTS & OTHER AT TACH MENTS
Tow only the attachments that are recommended by and
comply with specifications of the manufacturer of your trac-
tor. Use common sense when towing. Too heavy of a load,
while on a slope, is dangerous. Tires can lose traction with
the ground and cause you to lose control of your tractor.
SERVICE MINDER/HOURMETER
Service Minder shows the total number of hours the engine
has run and indicates when the engine or mower needs
servicing. After every 50 hours of operation the oil can
icon will stay on for 2 hours or until a manual reset occurs.
To reset the display manually turn the ignition switch to
the on position, then the off position five times (1 second
on, 1 second off). To service engine and mower, see the
Maintenance section of this manual.
NOTE: Service Minder runs when the ignition key is in any
position but "STOP". For accurate reading, ensure key
remains in the "STOP" position when engine is not running.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped from the fac-
tory already filled with sum mer weight oil.
Check engine oil with tractor on level ground.
Pull up and remove oil fill cap/dipstick; wipe oil off.
Reinsert the dipstick into the tube and push down firmly
into place. Remove and read oil level. If necessary,
add oil until "FULL " mark on dipstick is reached. Do
not overfill.
For cold weather operation you should change oil for
easier starting. (See "OIL VISCOSITY CHART" in the
Maintenance sec tion of this manual.)
To change engine oil, see the Maintenance section in
this manual.
13

Hide quick links:

Capítulos

Tabla de contenido
loading

Tabla de contenido