Optional Accessories - Virutex TM33W Manual De Instrucciones

left or right until the index marks 45º or any of the standard
positions (15º, 22º30', 30º, 45º).
Should you wish to make a cut that does not match any of
the plate's standard positions, push down lever E2 (Fig. 3) and
then push it towards trigger E3 (Fig. 3). This will unlock the
plate, enabling you to regulate the exact angle you require.
Then lock the plate using knobs K (Fig. 3).
7.4 CUTTING AT 45° x 45°
Press down lever E2 (Fig. 4) and turn the plate towards the
left until it locks into place at 45º. Loosen handle D and
lower the head to the stop at 45º or the intermediate angle
you wish. Lock it in place once again (Fig. 4).
The machine also enables you to tilt the head to any position
on the plate (only by turning it to the left).
Ensure that the moving arm is well secured
in position when mitering.
7.5 SPECIAL CUTS 200 x 25 mm
In the 0°x0° position this machine can make cuts up to 200
x 25 mm. For these cuts must be placed on the lower table
to do this, just fit supplements N2 (Fig.16) ref. 3346388
supplements for 200 mm cuts (optional accessory) to the
bottom table and then the cut can be made as normal. This
is possible due to the retractable saw protector R (Fig. 16)
which retracts as the cut is made.
7.6 MULTIPLE CUTS
To make multiple cuts the length stop A1 must be installed
and regulated to the required measurement (Fig. 5)
8. CUTS ON THE UPPER TABLE
The laser guide also includes an On/Off
switch T1 (Fig. 22) to activate or deactivate
it. The switch must be turned to 'Off' for
cutting on the upper table.
On the upper table only plastics and wood
can be cut, never aluminium or angles.
To use the machine in this cutting mode the lower cover K1
(Fig. 6) should be positioned on the machine which prevents
any accidental contact of the saw disc under the table. Next,
lock the machine in the transport position through axis M2
(Fig. 6), checking that the cowling is perfectly housed and
immobilised. Release knob A and lower the handle (Fig. 8),
ensuring that the cowling wedge Z6 is perfectly entered
through the lower part of the handle (Fig. 25).
Release knob L, withdraw the upper aluminium angle which
covers the blade protector and use it as a lateral cutting
guide, locking it again at the required distance from the
saw (Fig. 11), this protector has a side slot that includes
6
two nuts E4 (Fig. 11) designed to lock the wooden fillet
that extends up to the vertical axis of the centre of the
saw blade. Placing this wooden fillet (Fig. 17) is necessary
when making short cuts (dowels or stocks). This is because
in this type of cutting, when the cut piece is ejected from
the centre of the leaf, if it lacks space in coming out, the
turning of the blade, which could cause the accidental
expulsion of the part, will retain it.
The exit position of the saw with respect to the table is
regulated by releasing knobs M (Fig. 1) and placing the table
at the required cutting height, using the height adjustment
knob M2, ensuring that the blade overhangs the material to
be cut only at the level of the tooth, tighten up the knobs
at the selected height.
Lock button E1 in place for cutting with a raised table (Fig. 8).
Once the cutting work on the table is finished replace the
aluminium angle in the protection position before using
the machine as a mitre saw again.
As a safety measure, the machine will not
start in the absence of the cowling or its
faulty positioning.
Use push stick E5 supplied with this machine
to feed in the part to the saw blade (Fig.
21). The machine is equipped on one of the
sides of the upper table with two fastening
supports with which to attach the E5 thrust
rod during transport.
Use the upper protector of the upper blade
correctly.
Ensure that the tilting arm is well secured in
position when working on the upper table.
Immediately fit the main divider knife with the guard after
finishing work with the low profile divider knife.
Always keep the antikickback teeth well sharpened
Place the upper guard after finishing cutting work with the
upper table, the machine will not operate in mitre saw mode
without the upper guard correctly in place, ensuring that
the wedge Z7 is entered into its socket (Fig. 31).
9. DUST COLLECTION OUTLET
On the rear of this machine there is a Ø 38 mm dust collection
outlet, where it is possible to connect up a flexible tube,
adapting an industrial aspirator or any system of centralised
aspiration for collecting dust and shavings. We recommend
connection to our aspirators AS182K, AS282K.
For work on the upper table, and in addition to the connection
mentioned above, the fairing is provided with a nozzle D2
(Fig. 6) to which the standard dust collector attachment (Ref.
6446073 3.5 m / Ref. 1746245 5 m) must be connected for
perfect collection of the shavings.
We recommend you keep the machine permanently con-
nected to a dust and shavings collection system.

10. OPTIONAL ACCESSORIES

Ref. 3345416 Set of two pressers (Fig. 20). It is indispensable
for cutting aluminium and plastic profiles.