Dimplex TOLUCA DELUXE-EU Manual De Usuario página 4

Operating Instructions:
Please see Fig. 3
Icon Display Funtion
Power /
A
-
Standby
Flame
+
Up
Flame
-
B
Down
Flame
fC
Cycling
-
Off
Low
Heat
C
High
Heat
Cool
Blow
- Off
Back
D
-
Light
Temp
E
-
Down
Temp
E
-
Up
Sleep
F
Timer
Volume
-
G
down
Volume
-
G
Up
Blue-
H -
tooth
LED
I
-
COLOUR
Description
Press Once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
'FLAME EFFECT' button this turns the flame effect ON or OFF independently of the
products other features.
This Button will increase the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
This Button will decrease the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the flame effect to cycle from F2 to F5 in a continuous Loop.
This will turn the flame effect off. If the heater is ON, the display will activate and remain
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the flame effect is 'ON' the display will turn off after 5 seconds, however if the
heater is being used independently of the flame effect. The low heat or high heat icon
will appear continuously in the display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW HEAT'
icon. To Adjust the temperature setting the Temp Down or Temp Up buttons described
below must be used.
(This icon is Orange in Colour)
This icon in the display indicates 'HIGH HEAT' this setting will be indicated by the 'HIGH HEAT'
icon. To Adjust the temperature setting the Temp Down or Temp Up buttons described
below must be used.
(This icon is Red in Colour)
This icon in the display indicates 'COOL BLOW' this setting will be indicated by the 'COOL
BLOW' icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
Pressing this button will turn ON and OFF the Back Lighting. There are 4 settings, Sides
only, Top only, all OFF and All ON
Press multiple times to lower the heater temperature in 1
temperature that can be set is 18
Press multiple times to increase the heater temperature in 1
temperature that can be set 30
When High Heat is selected, the letters 'HH' appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the 'SLEEP TIMER' displays.
(This icon is Green in Colour)
Pressing multiple times to control the volume level of the speaker down to mute.
When Bluetooth is not connected, the speaker will play sound of a fire, this can be
turned OFF by pressing this button until the sound is muted.
Controls the level of the speaker Volume up.
The volume buttons can also control the volume of your paired bluetooth device
When a device is paired to the product, pressing this button will disconnect the paired
device.
Press multiple times to change the colour of the LED mood lighting and the coloured
fuel bed. The colour can be set as Orange, Red, Green, Blue, or cycling through all four
colours continuously.
C.
0
C.
0
C increments. The lowest
0
C increments. The highest
0