Vcr/Dvd Switching; Preset For Use; Turn On The Unit For The First Time - Sanyo DVW-7100A Manual De Instrucciones

H9680UD_EN/SP.qx3 04.8.10
Front Panel Display
Lights up when power is on.

VCR/DVD Switching

Pressing the OUTPUT button on the front panel
switches the output signal. (The VCR or DVD
OUTPUT light is lit.)
However, when using the remote control, you
must press the DVD or VCR button on the
remote control first.
• To use the VCR, press the VCR button on the
remote control.
(Verify that the VCR OUTPUT light is lit.)
• To use the DVD player, press the DVD button
on the remote control.
(Verify that the DVD OUTPUT light is lit.)
Note
• This remote control cannot operate your TV.

Preset for Use

Turn on the unit for the first
time
VCR
Press the VCR button first.
VCR VCR VCR
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section.
2
2
POWER
Remote Control
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
or
4:26 PM Page 9
Lights up when the progressive scan
system is activated.
Lights up during a recording.
Flashes when a recording is paused.
POWER POWER
REC REC T MER EC T MER EC
REW REW FFWD STOP STOP EJECT JECT PLAY REC OTR REC OTR
AV INP V INPUT
VIDEO VIDEO AUD O AUD O
Lights up when the timer recording
or an OTR recording has been set.
3
3
Do you connect the cable from the cable box or
the satellite box to the DVD+VCR's ANT-IN jack?
YES
Y es
Y es
Press the MENU
button to exit.
• Refer to "Hint for Cable Box
or Satellite Box" section on
page 6.
TV Screen
No
o
Please wait for a few minutes.
After scanning...
[ON]
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the
OPEN OPEN/CLOSE CLOSE
VCR VCR DVD DVD PROG ESS VE PROG ESS VE
CHANNEL CHANNEL OUTPUT OUTPUT SKIP SKIP REV REV STOP STOP PLAY FWD PLA WD/SK P SK P
P N C O E P N C O E
P WER P WER
EW EW F WD S S P P J CT J CT P AY E E / TR TR H N E H N E O T UT O T UT S OP S OP
V EO V EO AU IO AU IO
VCR VCR DVD DVD
OUTPUT
DVD OUTPUT
light
VCR OUTPUT
light
OUTPUT button
Need help? Call
Hint Hint
CH 01
• Repeat these steps only if either there
was a power failure or this unit has been
AUTO SET UP
unplugged for more than 30 seconds.
TIP:
If you change the on-screen language at
step [2], change the language for DVD func-
tion in "PLAYER MENU" setting. (Refer to
page 20.)
NO
B button once again.
– 9 –
Lights up when
the inserted disc
is being played
back.
Flashes when an
unacceptable disc
is installed.
POWER SPEED AUD O
P P Y Y WD WD K P K P
1 2 3
SK P CH
4 5 6
VCR TV
VCR
7 8 9
SLOW
button
0 +10
VCR DVD
DISPLAY PAUSE
DVD
PLAY
button
STOP
REC OTR
MENU
ENTER
SETUP TOP MENU RETURN
SEARCH CLEAR
MODE V SURR
MODE C RESET
SUBT TLE ANGLE
REPEAT
-SET
1-800-813-3435
A-B
EN