Explanation Of The Controls - Martin Yale intimus POWER 15.90 S Instrucciones De Uso

GB
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
OPERATING FUNCTIONS (Figs. 5 and 6):
1 = Main switch (Emergency-stop) (fig. 5)
This switch turns the machine either on
(position „1") or off (position „0").
When the „Ready" lamp (7) on the control
display remains on without blinking, this
means the machine is operating correctly.
A blinking lamp indicates a fault.
Note: There is a delay of about 2 seconds
before the lamp comes on (due to the mic-
roprocessor initialization routine).
2 = Locking switch (fig. 5)
Turning the key to the left locks the machi-
ne providing protection from unauthorized
use.
Note: Locking the machine when the main
switch (1) is on will cause the „Ready" lamp
(7) to start blinking. This indicates that the
machine is not Ready.
3 = „Cutting system forward"
pushbutton (fig. 5)
Pressing this button starts the cutting system
and the conveyor belt. Material can now be
fed to the shredder.
4 = „Cutting system stop"
pushbutton (fig. 5)
Pressing this button switches the shredder
off, thereby halting the cutting system and
the conveyor belt.
3
4
5
2
1
Fig. 5

EXPLANATION OF THE CONTROLS

5 = „Cutting system reverse"
pushbutton (fig. 5)
Pressing this button starts the cutting system
and the conveyor belt in reverse.
Note: Pressing this button while the machine
is in forward mode will cause it to run in
reverse mode for at least 3 seconds before
returning automatically to forward mode.
6 = „Cutting system forward"
indicator lamp (fig. 5)
a) Continuously lit when the cutting system
and conveyor belt are running in forward
mode.
b) Starts blinking when the cutting system
and conveyor belt are switched from
forward mode to reverse mode.
7 = „Ready" indicator lamp (fig. 5)
Continuously lit (indicating Ready)
when:
a) the main switch (1) is switched on,
b) the locking switch (2) is unlocked,
c) the emergency-stop rail (14) is pulled
out, and
d) the shredder bin (23) is fully docked.
Starts blinking (indicating not ready) when
the main switch is on, if:
a) the locking switch (2) is engaged, or
b) the emergency-stop rail (14) is
pressed.
6
7
8
9
10
11
12
13
8 = „Motor fault" indicator lamp (fig. 5)
9 = „Shredder bin full" or „bin not docked"
indicator lamp (fig. 5)
10 = „Cutting system reverse"
indicator lamp (fig. 5)
11 = Only relevant in conjunction with the ma-
12 = Only relevant in conjunction with the ma-
13 = Only relevant in conjunction with the ma-
14 = Emergency-stop rail (fig. 6)
11
15.90 S/16.50 S
Starts blinking when the shredder motor is
overloaded, thereby activating the built-in
thermal protection. This leads to a break in
the circuit necessary for active operation.
For more information please turn to the
section headed „Motor Fault".
Comes on when the Shredder bin is full and
needs to be emptied, or when the bin is not
fully docked. When this lamp comes on the
machine stops automatically.
For more information please turn to the
section headed „Emptying the shredder
bin".
Comes on when the cutting system is running
in reverse mode.
terials compactor (hydraulic bailer) - Type
860.
terials compactor (hydraulic bailer) - Type
860.
terials compactor (hydraulic bailer) - Type
860.
Should it be necessary for any reason
to switch the machine off as quickly as
possible, this can be done by pressing the
emergency-stop rail. In order to switch the
machine on again: release the rail by pulling
it out and push the „cutting system forward"
button (3).
14
Fig. 6