JB Systems Light LED PANEL Manual De Instrucciones página 6

ENGLISH
OPERATING INSTRUCTIONS
A. Standalone 1unit:
 Just connect the unit to the mains and put on some music. The unit starts working automatically to the
rhythm of the music.
Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
 Connect 2 to maximum 16 units together. Refer to the chapter "electrical installation" to learn how to
do this (don't forget to address all units properly!)
 Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music and show the internal chase programs.
Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
IMPORTANT REMARK:
When you use this LED PROJECTOR with a CA-8 controller and you select MANUAL mode
(mode LED = ON), the projector reminds the last setting used with controller, even after
disconnecting the controller and/or the mains voltage. If you don't want this, make sure to
select another working mode (mode LED must blink or off) before you unplug the controller.
BUTTON
STANDBY
Strobe 9 Color select
White  Red 
1.Synchronous strobe
Orange  Yellow 
in white color
FUNCTION
Green  Cyan 
2.The same color
Blue  Purple 
chase
3.Differentcolor Magenta
strobe
Sound 1 Manual
MODE
(LED OFF) (LED ON)
D. Controlled by universal DMX-controller:
 Connect all units together. Refer to
the chapter "Electrical installation for
two or more units in DMX-mode" to
learn how to do this (don't forget to
address all units properly!)
 Connect all units to the mains and turn
on the DMX controller.
Since each unit has its own DMX-
address, you can control them
individually. Remember that each unit
uses 4 DMX-channels as shown in the
DMX chart.
JB SYSTEMS
®
OPERATION MANUAL
ACTIONS
To blackout all the fixtures
Color Chase Color Fade
1. The same color 1. Fast speed
2. Different color 2. Middle speed
3. One light chase 3. Slow speed
4. Two lights chase
5. Four lights chase
Sound 2 Auto
(LED slow blinking) (LED fast blinking)
7/40 LED PANEL
ENGLISH
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch the unit off and unplug the mains cable.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical part is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 The cleaning of internal and external optics must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly
dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
SPECIFICATIONS
Mains Input: AC 100V~240V 50/60Hz
Fuse: 250V 2A slow blow (20mm glass)
Sound Control: Internal microphone
DMX connections: XLR 3pin
LEDs: 72 high power LEDs (R24 + G24 + B24)
Size: 300x300x137mm, see drawing below
Weight: 1,2kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS
®
OPERATION MANUAL
8/40 LED PANEL