Idiomas disponibles
Idiomas disponibles
The machine is intended for dry sanding and polishing of
wood, plastic, metal, filler, as well as for painted
surfaces. It is ist especially suitable for profiles, corners
or hard to reach locations.
Please refer to the booklet included in delivery for the
safety instructions.
Machine-specific Safety Warnings
Use the machine only for dry sanding. Penetration of
Ÿ
water into the machine increases the risk of an electric
shock.
Caution, fire hazard! Avoid overheating the object
Ÿ
being sanded as well as the sander. Always empty
the dust collector before taking breaks. In
unfavourable conditions, e. g., when sparks emit from
sanding metals, sanding debris in the dust bag, micro
filter or paper sack (or in the filter sack or filter of the
vacuum cleaner) can self-ignite. Particularly when
mixed with remainders of varnish, polyurethane or other
chemical materials and when the sanding debris is hot
after long periods of working.
Secure the workpiece. A workpiece clamped with
Ÿ
clamping devices or in a vice is held more secure than
by hand.
Keep your workplace clean. Blends of materials are
Ÿ
particularly dangerous. Dust from light alloys can burn
or explode.
Never use the machine with a damaged cable. Do
Ÿ
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
Functional Description
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Please read the operating instructions carefully before
assembling and using.
Assembly
Fitting the dust bag (Fig. 2)
Important! For health safety reasons it is imperative that
you use a dust bag
.
Fastening the sanding/grinding paper (Fig. 4)
-
Pull out the power plug first.
-
Insert the sanding/grinding paper into the open clamp
and close the clamp.
-
Lay the sanding/paper over the oscillating plate so
that the paper is taut and clamp it again
-
Make sure that the perforations in the sanding/grinding
paper coincide with the oscillating plate
ENGLISH
7
Layout (Fig. 1)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Placement and Testing
ON/OFF switch (Fig. 3)
To switch on: Press switch 2
Continuous operation: Secure switch 2 with locking knob 4.
To switch off: Briefly hold down switch 2. You can preselect
the speed by turning the knurled screw in switch 2.
Tool change
Carbon brushes
-
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician
Important! The carbon brushes should not be
remplaced by anyone but a qualified electrician.
Cleaning, maintenance and ordering of spare
parts
Always pull out the mains power plug before starting any
cleaning work
Cleaning
-
-
-
-
Repair service
The technical service will provide you advice regarding
questions you may have on the repair and maintenance of
your product as well as on spare parts. You may also obtain
exploded views and information on spare parts on the
internet under: [email protected]
Disposal and recycling
The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
.
.
7
Front handle
ON/OFF switch
Speed controller
Locking knob
Handle
D
ust bag
Sanding/grinding plate
Clamping device
Suction outlet
.
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible
Wipe the equipment with a clean cloth or blow it with
compressed air at low pressure.
We recommend that you clean the tool immediately
after you use it
.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents or
solvents; these may be aggressive to the tool's
plastic parts. Ensure that no water can get into the
interior of the tool.
.
.
