Candy DUO 609 X Manual De Instrucciones página 4

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect
consumer safety.
It is for this reason that a professionally qualified person should undertake the task who will carry it out in accordance
with the technical regulations in force.
In the event that this advice is ignored and the installation is carried out by an unqualified person, the manufacturer declines
all responsibility for any technical failure of the product whether or not it results in damage to goods or injury to individuals.
ELECTRICAL CONNECTION
"The installation must conform to the standard directives".
The manufacturer declines all responsibility for any damage that
may be caused by unsuitable or unreasonable use.
Warning :
• Always check before any electrical operation, the supply tension
shown on the electricity meter, the adjustment of the circuit-
breaker, the continuity of the connection to earth to the installation
and that the fuse is suitable.
• The electrical connection to the installation should be made via
a socket with a plug with earth, or via an omni pole cut-out
switch.
If the appliance has a socket outlet, it must be installed so that
the socket outlet is accessible.
The manufacturer cannot be held responsible for any accidents
resulting from the use of an appliance which is not connected
to earth, or with a faulty earth connection continuity.
• Any queries regarding the power supply cord should be referred
to After Sales Service or a qualified technician.
Warning! This appliance must be earthed. In the absence of
adequate earthing you will notice that when touching the
metal parts of your appliance an electrical dispersion can be
felt due to the presence of a radio interference suppressor.
• DUO
A power cord is supplied with the DUO which allows it to be
connected only to a power supply of 220-240 V between
phases, or between phase and neutral.
• Connect to a 10/16 Amp socket.
WATER CONNECTION - WATER DRAINAGE
WATER CONNECTION :
The inlet and drain hoses can be directed to left or right.
The dishwasher can be connected to either cold or hot water, as
long as it is no hotter than 60°C.
Water pressure must be between 0,08 MPa and 0,8 MPa. If the
pressure is below the minimum consult the service department
for advice.
The inlet hose must be connected to a tap so that the water supply
can be cut off when the machine is not in use (fig.1). The dishwasher
inlet hose is fitted with a 3/4" threaded connector (fig.2). The inlet
hose "A" should be tightly connected to a 3/4" tap "B".
The water connection of the dishwasher must be done exclusively
with the pipe supplied.
Do not use an old pipe.
If the machine is connected to new pipes or to pipes which have
not been in use for long time, run water through for a few minutes
before connecting the inlet hose. In this way no deposits of sand
or rust will clog up the water inflow filter.
INSTALLATION
WATER DRAINAGE :
Take care not to bend or kink the drain hose when connecting it
to the machine so that the water can drain freely from it (fig.3y).
The drain hose must be at least 40 cm above floor level and it
must have an internal diameter of at least 4 cm. It is advisable to
fit an anti-odour air trap (fig.3x).
If necessary, the outlet hose can be extended up to 2,6 m, provided
that it is kept at a maximum height of 85 cm above floor level. For
this, contact Customer Service.
4
3
The hose can be hooked over the side of the sink (it must not be
immersed in water, in order to prevent water from being siphoned
back to the machine when this is in operation) Check that there
are no kinks in the inlet and outlet hoses. To extend, if necessary
the intlet hose, contact the Customer Service.
The mounting of the profile should be done during installation.
If not, please provide 1 cm between the top of the appliance
and the bottom of the work surface for air circulation, and
position the spacer delivered with the appliance.
2 GB
WARNING!
D