Adjusting The Harness Height - KIKKA BOO SENIOR Instrucciones De Uso

c) Push the car seat towards the back of vehicles seat(A)
6
d) Match the isofix anchors to the vehicles anchoring point until you hear a "click"(B)
e) Rotate the adjuster button in an anti-clock wise direction(C),and push the car seat to the back of vehicles seat as much as possible(D)
7/8
f) Hook the top tether up and pull as tight as possible(A)
Ensure that you have first installed the child car seat correctly, following the steps under 'Installing for Group I [918kg]' ,
9
Press button (B) and pull up on the shoulder straps (not the shoulder pads) to loosen the straps. Press button (A) and unfasten the harness.
IMPORTANT: DO NOT pull the shoulder pads.
Place the harness straps over the side of the shell (C), position your child in the child car seat (D) ensuring no toys or other hard objects are in the seat.
10
Match the two halves of the harness buckles together and insert them into the crotch buckle (E). Make sure the shoulder straps fit your child snugly
by pulling the adjuster belt (F).

ADJUSTING THE HARNESS HEIGHT

Attention: You should not attempt to adjust the harness height with a child in the child car seat.
The harness strap slots should be level with or above your child's shoulders.
11
If they are not, then you may need to reposition the harness shoulder straps and adjust the harness height.
Adjust the shell to its most reclined position. Pull the recline adjuster handle under the front of the shell and whilst holding it, pull the shell forwards
12
to its most reclined position.
Press button (A) and pull up on the shoulder straps (not the shoulder pads) to completely loosen the straps. Ensure you loosen the shoulder straps
13
completely as this will aide the harness removal. IMPORTANT: DO NOT pull the shoulder pads.
14
Remove the installation bar (B) by pulling the lock (C) up, on the top right hand side of the shell.
15
Pull and hold the shell forward.
Unhook the straps at the rear of the seat shell by sliding the straps through the slits in the shoulder pads connector (D) and yoke (E).
16
NOTE: The thinner straps are the shoulder pad straps, and they connect to the shoulder pads connector (D) and the wider straps are the shoulder
harness straps, and they connect to yoke (E).
Adjust one side at a time.
17
Pull one set of shoulder straps through their slot (F) and avoid twisting the straps. Pass both the wider strap (H) and narrow strap (I) back through
the shell at your desired slot height (G),making sure the wider strap (H) is threaded through the shoulder pad (J), and that you keep the thinner strap
(I) below the wider strap (H). Repeat on the opposite side.
Check none of the straps are twisted and reconnect the shoulder pad straps to the shoulder pad connector (D) and the shoulder harness straps to the
18
yoke (E). Return the shell to its original position and re-insert the installation bar (M) and secure lock (N).
CONVERTING FOR CHILDREN IN GROUP II [15-25KG]
It is recommended that you use the 5-point harness for as long as possible. Try removing the booster cushion as this could allow you to use the seat
19
in group I configuration for longer. When your child has outgrown the group I (9-18kg) configuration or you wish to use the seat for a child 15-25kg,
then you will need to convert the child car seat to group II mode. You will need to remove the child car seat's integral 5-point harness.
Press button (A) and pull up on the shoulder straps (not the shoulder pads) to completely loosen the shoulder straps and shorten the adjuster strap
(B) as much as possible. IMPORTANT: DO NOT pull the shoulder pads.
Adjust the shell to its most reclined position.
20
Pull the recline adjuster handle under the front of the shell and whilst holding it, pull the shell forwards to its most reclined position.
21
Remove the installation bar (C) by pulling the lock (D) up, on the top right hand side of the shell.
22
Pull and hold the shell forward.
23
Unhook the shoulder pad straps from shoulder pad connector (E). Unhook the shoulder harness straps from yoke (F).
Pass the shoulder straps through the slots in the back of the shell (G).
24
Locate the two metal retainer buckles (FI) under the seat cover at points (1) and (2). Pass the metal buckles on the waist harness from the front of
the shell, through the inner slots (I) on the back of the shell and back out the outer slots (J), to the front to remove the harness. If your child does not
need the booster cushion (K) it can be removed.