stayer SA21-180 Manual De Instrucciones página 18

gb
This manual is consistent with the date of manufacture
of your machine, you will find information on the
technical data of the machine acquired manual check
for updates of our machines on the website:
www.grupostayer.com
The machine is intended for cutting, roughing,
and brushing metal and stone materials
without using water. With approved sanding
tools, the machine can be used for sanding
with sanding discs.
1_MACHINE-SPECIFIC SAFETY
WARNINGS
Safety Warnings Common for Grinding, Sanding,
Wire Brushing or Abrasive Cutting-Off Operations
This power tool is intended to function as a grin-
der, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and spe-
cifications provided with this power tool. Failure to fo-
llow all instructions listed below may result in electric
shock, fire and/or serious injury.
This power tool is not recommended for polishing.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
Do not use accessories which are not specifically
designed and
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately guarded or controlled.
The arbor size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle
of the power tool. Accessories with arbor holes that
do not match the mounting hardware of the power tool
will run out of balance, vibrate excessively and may
cause loss of control.
Do not use a damaged accessory. Before each use,
inspect the accessory such as abrasive wheels for
chips and cracks, backing pads for cracks, tears
or excess wear, wire brushes for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run the
power tool at maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses.
recommended by the
inspecting and installing
As appropriate,
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
Keep bystanders a safe distance away from the
work area. Anyone entering the work area must
wear personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
Hold the power tool only by the insulated gripping
surfaces when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and shock
the operator.
Position the cord clear of the spinning accessory.
If you lose control of the power tool, the cord may
be cut or snagged and your hand or arm may be
pulled into the spinning accessory. Never lay the
power tool down until the accessory has come to a
complete stop. The spinning accessory may grab the
surface and pull the power tool out of your control.
Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
tool
your body.
Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding. For example, if an abrasive wheel is snagged
or pinched by the workpiece, the edge of the wheel that
is entering into the pinch point can dig into the surface
of the material causing the wheel to climb out or kick
an
out. The wheel may either jump toward or away from
the operator, depending on direction of the wheel's
movement at the point of pinching. Abrasive wheels
may also break under these conditions. Kickback is the
result of power tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking
proper precautions as given below.
- 18 -
wear dust mask, hearing