DeWalt D25481 Serie Manual De Instrucciones página 22

ENglIsh

WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/
or bit onto to the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle 3
Fig. F
4
2
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
6. To stop the hammer, release the switch.
Recommendations for Tool Operation
• Large (5/16" to 1/2" [7.9 mm to 12.7 mm]) holes in steel
can be made easier if a pilot hole (5/32" to 3/16" [4 mm
to 4.8 mm]) is drilled first.
• When drilling, always apply pressure in a straight line
with the bit, but do not push hard enough to stall the
motor or deflect the bit. A smooth even flow of material
indicates the proper drilling rate.
• If drilling thin material or material that is prone to
splinter, use a wood "back-up" block to prevent damage
to the work piece.

WARNING:
• Do not use this tool to mix or pump easily
combustible or explosive fluids (benzine,
alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Lubrication
Your power tool requires no additional lubrication.
20
, select the mode
4
as necessary.
1
1 .
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Various types of SDS Max drill bits and chisels are available
as an option. Accessories and attachments used must be
regularly lubricated around the SDS Max fitment.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D WALT factory service center
e
or a D WALT authorized service center. Always use
e
identical replacement parts.
Protecting the Environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. .
Specifications
D25481-AR
220V ~
Voltage
50Hz
Power
1050W
0-540/min
No load speed
(rpm)
Impacts per minute
3150 imp
WALT
e
D25481-B2 D25481-B3 D25481-BR
220V ~ 120V ~ 127V ~
50-60Hz 50-60Hz 60Hz
1050W 1050W 1050W
0-540/min 0-540/min 0-540/min
(rpm) (rpm) (rpm)
3150 imp 3150 imp 3150 imp