Heat Gun Safety Warnings - Hitachi RH 600T Instrucciones De Manejo

PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach
of children and infi rm persons.

HEAT GUN SAFETY WARNINGS

Important Warning:
1. If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualifi ed person in order to avoid a hazard.
2. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
3. Children should be supervised to ensure that they do
not play with the appliance.
4. A fi re may result if the appliance is not used with care,
therefore
Be careful when using the appliance in places where
there are combustible materials.
Do not apply to the same place for a long time
Do not use in presence of an explosive atmosphere
Be aware that Heat may be conducted to combustible
materials which are out of sight
Place the appliance on its stand after use and follow it to
cool down before storage
Do not leave the appliance unattended when it is
switched on
WARNING
1. Do not use the tool or touch the power plug with wet
hands.
Failure to observe this may result in electric shocks.
2. Always check the work area prior to use, and do not use
the tool if safety cannot be guaranteed.
Failure to observe this may result in infl ammable
articles concealed in or behind invisible areas (cases,
ceilings, fl oors, hollow areas) being ignited.
3. Do not use the tool in the vicinity of volatile substances
(thinner, gasoline, etc.)
Failure to observe this may result in the outbreak of fi re
or explosions.
4. Do not stand underneath when using the tool in elevated
locations.
Also, do not catch the power cord on anything, or allow
it to be pulled.
Failure to observe this may result in accidents.
SPECIFICATIONS
Voltage
Frequency
Input
Air volume
Capacity
Air temperature
Engine Model
Weight
5. Do not point the hot wind directly at people or animals.
Do not look into the nozzle. Do not use it as a hair dryer
under any circumstances.
Failure to observe this may result in accidents or injury.
6. There are cases in which highly toxic gas will be emitted
if used on plastic, lacquer or similar materials.
Always ensure that the work area is fully ventilated, and
wear a dust-protection mask.
7. Apply heat gently while moving the Heat Gun up, down,
left and right.
Aiming it constantly at a single location may result in the
outbreak of smoke or fi re.
8. Check the tool for damage, cracks or malformation in
the event of it being accidently dropped or subject to
impact.
Damage, cracks and malformation may result in injury.
9. Cease operations immediately in the event of the
tool not operating properly or if abnormal noises or
vibrations are noticed, and contact a Hitachi Authorized
Service Center to request inspections and repairs.
Continued use may result in injury.
10. Do not get away from the unit while it is switched on.
Failure to observe this may result in accidents.
CAUTION
1. Parts of the nozzle supplied are sharp, so use gloves
when removing them from the case and when attaching
or detaching them.
2. The hot wind release nozzle, the tip of the nozzle and
the material that was heated are extremely hot during
and immediately after using the tool, so use gloves and
avoid touching them directly.
3. Do not use inside boxes, drawers or other enclosed
spaces.
Aiming it constantly at a single location may result in the
outbreak of smoke or fi re.
4. Make sure the nozzle is at least 5cm away from the item
being heated when using the tool. Also, do not cover or
otherwise block the nozzle.
Failure to observe this may result in the Heat Gun
overheating, leading to malfunctions.
5. Do not switch the tool on and off repeatedly. Also, do not
use the tool with the power cord folded or twisted.
Failure to observe this may result in malfunctions.
6. Do not point the heat-wind release nozzle downwards
immediately after use.
Failure to observe this may result in the tool overheating,
leading to malfunctions.
7. Make sure that the Heat Gun has cooled completely
before storing it away.
Failure to observe this may result in burns or
malformation of the storage case.
127 V
60 Hz
1800 W
0.25 m /min to 0.5 m
3
350°C – 500°C
2-stage switch
50°C
(When the cooling button is used.)
/min (2-stage switch)
3
450°C – 600°C
(When the cooling button is used.)
Engine of direct current
Equipment of class II
0.57 kg
English
220 V
60 Hz
1800 W
2-stage switch
50°C
5