Mitsubishi Electric PAC-IF021B-E Manual De Instalación página 19

. Remote controller operation
[Detailed setting]
[4]-1 CHANGE LANGUAGE setting
The language that appears on the dot display can be selected.
• Press the [ MENU] button G to change the language.
1 English (GB), 2 German (D), 3 Spanish (E), 4 Russian (RU),
5 Italian (I), 6 French (F), 7 Swedish (SW)
Refer to the dot display table.
[4]-2 Function selection setting
(1) Operation function limit setting (operation lock)
• To switch the setting, press the [
1 no1: Operation lock setting is made on all buttons other than
the [ ON/OFF] button I.
2 no2: Operation lock setting is made on all buttons.
3 OFF (Initial setting value): Operation lock setting is not made.
* To make the operation lock setting valid on the normal screen,
it is necessary to press buttons (Press and hold down the [CIR.
WATER] A and [ ON/OFF] buttons I at the same time for 2
seconds.) on the normal screen after the above setting is made.
(2) Use of operation mode setting
When the remote controller is connected to the unit that has the op-
eration mode, the following settings can be made.
• To switch the setting, press the [
1 SELECT HEATING
ON· ····· HEATING mode can be selected.
OFF ···· HEATING mode is skipped.
2 SELECT HEATING ECO
ON· ····· HEATING ECO mode can be selected.
OFF ···· HEATING ECO mode is skipped.
3 SELECT HOT WATER
ON· ····· HOT WATER mode can be selected.
OFF ···· HOT WATER mode is skipped.
4 SELECT ANTI-FREEZE
ON· ····· ANTI-FREEZE mode can be selected.
OFF ···· ANTI-FREEZE mode is skipped.
5 SELECT COOLING
ON· ····· COOLING mode can be selected.
OFF ···· COOLING mode is skipped.
6 SELECT MODE OFF (Initial setting value)
The all operation mode is displayed when the mode is selected.
(3) Temperature range limit setting
After this setting is made, the temperature can be changed within
the set range.
• To switch the setting, press the [
1 LIMIT TEMP HOT WATER MODE:
The temperature range can be changed on hot water / heating
mode.
2 LIMIT TEMP ANTI-FREEZE MODE:
The temperature range can be changed on anti-freeze mode.
3 LIMIT TEMP COOLING MODE:
The temperature range can be changed on cooling mode.
4 OFF (initial setting): The temperature range limit is not active.
* When the setting other than OFF is made, the temperature
range limit setting on heating, hot water, anti-freeze, and
cooling mode is made at the same time. However, the range
cannot be limited when the set temperature range has not
changed.
• To increase or decrease the temperature, press the [
( ) or ( )] button F.
• To switch the upper limit setting and the lower limit setting, press
the [ INITIAL SETTING] button H. The selected setting will
blink and the temperature can be set.
ON/OFF] button D.
ON/OFF] button D.
ON/OFF] button D.
TEMP.
[4]-3 Mode selection setting
(1) Remote controller main/sub setting
• To switch the setting, press the [
1 Main: The controller will be the main controller.
2 Sub: The controller will be the sub controller.
(2) Use of clock setting
• To switch the setting, press the [
1 ON: The clock function can be used.
2 OFF: The clock function cannot be used.
(3) Timer function setting
• To switch the setting, press the [
one of the followings.).
1 WEEKLY TIMER:
The weekly timer can be used.
2 AUTO OFF TIMER:
The auto off timer can be used.
3 SIMPLE TIMER:
The simple timer can be used.
4 TIMER MODE OFF (Initial setting):
The timer mode cannot be used.
* When the use of clock setting is OFF, the "WEEKLY TIMER" can-
not be used.
(4) Contact number setting for error situation
• To switch the setting, press the [
1 CALL OFF:
The set contact numbers are not displayed in case of error.
2 CALL **** *** ****:
The set contact numbers are displayed in case of error.
CALL_:
The contact number can be set when the display is as shown
above.
• Setting the contact numbers
To set the contact numbers, follow the following procedures.
Move the blinking cursor to set numbers. Press the [
( ) and ( )] button F to move the cursor to the right (left).
Press the [ CLOCK ( ) and ( )] button C to set the num-
bers.
(5) Use of water temperature offset function
• To switch the setting, press the [
1 ON: The water temperature offset function can be used.
2 OFF: The water temperature offset function cannot be used.
* Refer to page 23 for details of offset function.
[4]-4 Display change setting
(1) Temperature display °C/°F setting
• To switch the setting, press the [
1 °C: The temperature unit °C is used.
2 °F: The temperature unit °F is used.
(2) Water temperature display setting
• To switch the setting, press the [
1 ON: Water temperature is displayed.
2 OFF: Water temperature is not displayed.
ON/OFF] button D.
ON/OFF] button D.
ON/OFF] button D (Choose
ON/OFF] button D.
TEMP.
ON/OFF] button D.
ON/OFF] button D.
ON/OFF] button D.
1