Makita BGD800 Manual De Instrucciones página 4

ENGLISH
(Original instructions)
1 Button
2 Red part
3 Battery cartridge
4 Slide switch
5 Indication lamp
SPECIFICATIONS
Model
Collet capacity ............................................................................. 6 mm or 6.35 mm (1/4")
Max. wheel point diameter .......................................................... 38 mm
No load speed (n ) / Rated speed (n) ........................................... 25,000 (min
o
Overall length .............................................................................. 402 mm
Net weight ................................................................................... 2.0 kg
Rated voltage ............................................................................... D.C. 18 V
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Specifications and battery cartridge may differ from
country to country.
• Weight, with battery cartridge, according to EPTA-Pro-
cedure 01/2003
Intended use
The tool is intended for grinding ferrous materials or
deburring castings.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS DIE GRINDER SAFETY
WARNINGS
Safety Warnings Common for Grinding Operation:
1. This power tool is intended to function as a
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
2. Operations such as sanding, wire brushing, pol-
ishing or cutting-off are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
4
Explanation of general view
6 Wrench 13
7 Wheel point
8 Collet nut
9 Wrench 13
10 Limit mark
5.
6.
ENE050-1
GEA010-1
7.
GEB080-1
8.
9.
10. Never lay the power tool down until the acces-
11. Do not run the power tool while carrying it at
11 Holder cap cover
12 Screwdriver
13 Brush holder cap
BGD0800
–1
)
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks. If power tool or
accessory is dropped, inspect for damage or
install an undamaged accessory. After inspect-
ing and installing an accessory, position your-
self and bystanders away from the plane of the
rotating accessory and run the power tool at
maximum no-load speed for one minute. Dam-
aged accessories will normally break apart during
this test time.
Wear personal protective equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As appropriate,
wear dust mask, hearing protectors, gloves and
workshop apron capable of stopping small abra-
sive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated
by various operations. The dust mask or respirator
must be capable of filtrating particles generated by
your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of opera-
tion.
Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
shock the operator.
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
BGD801
6 mm or 6.35 mm (1/4")
38 mm
–1
25,000 (min )
307 mm
1.7 kg
D.C. 18 V