Getting Started - Husqvarna Automower Connect 3G/2G Manual De Usuario

1.1 Introduction
1.1.1 Description
®
Automower Connect brings the menu system to your
mobile device, making it easy to read and change the
product settings remotely. Through this application, you
can receive the current status of the product and send
commands to the product from anywhere in the world. In
case of theft, you get an alarm and can monitor the
position of the product.
1.1.2 Installation
®
The Automower Connect accessory must be installed
by a dealer. The installation includes a software update
of the product.

1.2 Getting started

You can communicate with your product through the
mobile application Automower
®
Automower Connect activated, new symbols will show
on the display of the product.
Note:
All countries do not support Automower
Connect because of legal reasons and regional
specified cellular systems. The included Automower
Connect lifetime service only applies if there is a third
part sub-supplier of 2G/3G/4G available in the
operational area. In some countries Bluetooth
available due to legal reasons.
1.2.1 Download the Automower
app
®
Download the Automower Connect app from App Store
or Google Play to your mobile device.
1.2.2 Create an Automower
account
When you have downloaded the app, you can enter your
e-mail address and a password to make an Automower
Connect account. You will receive a validation e-mail to
your e-mail address. Follow the instructions in the e-mail
in less than 24 hours to validate your account. If not
validated in less than 24 hours, you must make a
account again. You can pair the product and your mobile
device when the account has been made in the app.
1.2.3 Pair with Automower
1. Start the app on your mobile device and log in to
your account.
Menu > My mowers .
2. Select
3. Push + to add a new product. Follow the
instructions in the app.
2 - Operators manual
1 Operators manual
®
Connect. With
®
®
®
is not
®
Connect
®
Connect
®
®
Connect
4. Select Menu > Accessories > Automower
Connect .
5. Enter the PIN code.
Pairing > New pairing in the menu of the
6. Select
product.
7. Enter the 6-digit code shown on the display of the
product.
1.3 Settings
Display and change the settings of the product from
everywhere in the world. For security reasons you must
use short-range communication (Bluetooth
change General and Security settings, or disable the
®
Automower Connect module on the product.
1.3.1 To set the GeoFence center
The GeoFence function makes it possible to monitor the
product, for example in case of theft. Before GeoFence
can be used, its center point and sensitivity must be set.
This can only be done from the menu in the product.
1. Put the product in the center of the work area.
Accessories > Automower
2. Select
3. Enter the PIN code.
GeoFence .
4. Select
Activate GeoFence and push OK.
5. Select
New center point to set the source for
6. Select
GeoFence.
GeoFence sensitivity can be changed. Sensitivity can be
Low, Medium or High . The higher the sensitivity,
set to
the easier the alarm is activated.
Note:
When you put the product into storage for a
long period, it is recommended to switch off the main
switch to save battery power. With the GeoFence
function on, a PIN code is necessary to switch off the
product. If you switch off the main switch, the
®
Automower Connect stays on for 12 hours. After that it
is not possible to communicate with the product and the
GeoFence function is not on.
1.3.2 Symbols on the display
These symbols are shown on the display of the product
®
when Automower Connect is enabled.
The signal strength of the GPRS
reception.
®
®
) if you
®
Connect .
1428 - 003 - 08.09.2020