Description; Assembly - GGP ITALY BLV 48 Li Manual De Instrucciones

DESCRIPTION / ASSEMBLY

4. DESCRIPTION

1. Variable switch
2. Low/high button
3. ON/OFF button
4. Auxiliary handle
5. Mulch/vacuum gate
6. Lock button
7. Blower tube
8. Mulcher tube
9. Bag
10. Notched area
11. Air outlet
12. Slot
13. Tab
14. Strap

5. ASSEMBLY

UNPACKING
■ Carefully remove the product and any accessories
from the box.
■ Inspect the product carefully to make sure no
breakage or damage occurred during shipping.
■ Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
■ If any parts are damaged or missing, please call your
Tools service centre for assistance.
The blower vac is supplied with some components not
assembled. To assemble these, proceed as follows:
ASSEMBLE AS A MULCHER
See Figure 2.
■ Slide the front and rear mulcher tubes together until
locked. (See fig 2)
■ Pull the lock button forward to disengage the gate.
Hold the gate open. (See fig 2.1)
■ Insert the "wedged" end clip of the mulcher tube into
the rear clip. (See fig 2.2). Push the "hooked" end
clip of the mulcher tube into the front clip. (See fig
2.3). Press the lock button back to engage the
mulcher tube. (See fig 2.4)
■ To remove mulcher tubes, follow the steps(3) (2) (1).
■ Insert the bag adaptor into the blower outlet. Lock
the bag adaptor with the lock button. To remove the
bag, simply press lock button and remove bag. (see
Fig.4).
NOTE: It may be necessary to remove the blower tube or
mulcher tubes to clear a blocked tube or impeller.
WARNING
To prevent serious personal injury, make sure the
switch is in the OFF position, it is unplugged, and the
impellers have stopped before attaching or removing
tubes.
ASSEMBLE AS A BLOWER See Figure 3.
■ Slide blower tube forward until the notched areas on
the blower housing click into the slots on the tube.
15. Identification plate
15.1) EC Conformity marking
15.2) Name and address of the manufacturer
15.3) Guaranteed sound power level
15.4) Machine model
15.5) Serial number
15.6) Year of manufacture
15.7) Power supply frequency and voltage
15.8) Motor power
15.9) Article Code
15.10) Manufacturing country
■ Insert the concentrator nozzle into the regular nozzle
to lock. (Concentrator nozzle is used to increase air
flow in tight areas: flower beds,under decks, etc)
INSTALLING BAG WITH SHOULDER HARNESS See
Figure 4.
■ While standing in the operating position adjust the
length to fit the operator's size. Pull the tab lengthen
, pull the strap to shoten.
For complete charging instructions, refer to the
Operator's Manuals for your battery pack and
charger models.
NOTE: To avoid serious personal injury, always remove
the battery pack and keep hands clear of the variable
speed trigger when carrying or transporting the tool.
TO INSTALL BATTERY PACK
See Figure 5.
■ Place the battery pack in the blower. Align raised rib
on battery pack with grooves in the blower's battery
port.
■ Make sure the latch on bottom of the battery pack
snaps in place and that battery pack is secured in
the blower before beginning operation.
When placing battery pack in the blower, be sure the
raised ribs on the battery pack align with the grooves
in the top of the blower. Make sure the battery is fully
seated, and it latches into place properly. Improper
installation of the battery pack can cause damage to
internal components.
TO REMOVE BATTERY PACK
See Figure 5.
■ Release the variable speed trigger to stop the blower.
■ Press and hold the button at the bottom of the
battery pack.
■ Remove battery pack from the blower.
EN
CAUTION
4