Hitachi DN 10DY Instrucciones De Manejo página 5

GENERAL OPERATIONAL PRECAUTIONS
1. Keep work area clean. Cluttered areas and benches
invite accidents.
2. Avoid dangerous environment. Don't expose power
tools and charger to rain. Don't use power tools
and charger in damp or wet locations. And keep
work area well lit.
Never use power tools and charger near inflam-
mable or explosive materials.
Do not use tool and charger in presence of in-
flammable liquids or gases.
3. Keep children away. All visitors should be kept
safe distance from work area.
4. Store idle tools and charger. When not in use,
tools and charger should be stored in dry, high
or locked-up place-out of reach of children. Store
tools and charger in a place in which the tem-
perature is less than 40°C.
5. Don't force tool. It will do the job better and safer
at the rate for which it was designed.
6. Use right tool. Don't force small tool or attach-
ment to do the job of a heavy duty tool.
7. Wear proper apparel. No loose clothing or jewelry
to get caught in moving parts. Rubber gloves and
footwear are recommended when working out-
door.
8. Use safety glasses with most tools. Also face or
dust mask if cutting operation is dusty.
9. Don't abuse cord. Never carry charger by cord or
yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
10. Secure work. Use clamps or a vise to hold work.
It's safer than using your hand and it frees both
hands to operate tool.
11. Don't overreach. Keep proper footing and balance
at all times.
12. Maintain tools with care. Keep tools sharp at all
times, and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
13. When the charger is not in use or when being
maintained and inspected, disconnect the power
cord of the charger from the AC outlet.
14. Remove chuck wrenches and wrenches. Form habit
of checking to see that wrenches are removed
from tool before turning it on.
15. Avoid accidental starting. Don't carry tool with
finger on switch.
16. Always use the specified charger.
Never use a charger other than that specified to
prevent danger.
17. Use only original HITACHI replacement parts.
18. Do not use power tools for applications other than
those specified in the Handling Instructions.
19. The use of any other accessory or attachment
other than recommended in this handling instruc-
tions or the HITACHI catalog may present a risk
of personal injury.
20. If the supply cord of this charger is damaged, the
charger must be returned to the HITACHI autho-
rized service center for the cord to be replaced.
Let only the authorized service center do the
repairing. The Manufacturer will not be respon-
sible for any damages or injuries caused by repair
by the unauthorized persons or by mishandling
of the tool.
21. To ensure the designed operational integrity of
power tools and charger, do not remove installed
covers or screws.
22. Always use the charger at the voltage specified
on the nameplate.
23. Do not touch movable parts or accessories unless
the power source has been disconnected.
24. Always charge the battery before use.
25. Never use a battery other than that specified. Do
not connect a usual dry cell, a rechargeable battery
other than that specified or a car battery to the
power tool.
26. Do not use a transformer containing a booster.
27. Do not charge the battery from an engine electric
generator or DC power supply.
28. Always charge indoors. As the charger and bat-
tery heat-up slightly during charging, charge the
battery in a place not exposed to direct sunlight,
which has low humidity and is well ventilated.
29. When working in a high place, pay attention to
activities below. Before commencing, ensure that
there are no people below.
30. The exploded assembly drawing on this handling
instructions should be used only for authorized
service facility.
PRECAUTIONS FOR CORDLESS ANGLE DRILL
1. Always charge the battery at a temperature of 5
– 40°C for UC12Y and 0 – 40°C for UC14YF/
UC14YF2. A temperature of less than 5°C will
result in over charging which is dangerous. The
battery cannot be charged at a temperature greater
than 40°C. The most suitable temperature for
charging is that of 20 – 25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
3. Do not charge the battery for more than 1 hour.
The battery will be fully charged in about 1 hour
and charging should be stopped when 1 hour has
elapsed from commencement. Disconnect the
charger power cord from the receptacle.
4. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
5. Never disassemble the rechargeable battery and
charger.
6. Never short-circuit the rechargeable battery. Short-
circuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
7. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
8. When drilling in wall, floor or ceiling, check for
buried electric power cord, etc.
9. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
10. Using an exhausted battery will damage the
charger.
11. Do not insert object into the air ventilation slots
of the charger.
Inserting metal objects lor inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
12. When mounting a bit into the keyless chuck, tighten
the sleeve adequately. If the sleeve is not tight,
the bit may slip or fall out, causing injury.
13. Do not wear gloves made of stuff liable to roll
up such as cotton, wool, cloth or string, etc.
14. Do not insert object into the air ventilation slots
of the body.
English
3