Maintenance And Inspection - Hitachi H 45MA Instrucciones De Manejo

(3) Adjust the groove position while turning the tool,
and furthermore insert it until it hits the end of the
hole.
(4) Return grip (A) to its original position, pull the tool
and make sure it is locked completely. (Fig. 2)
5. Deciding Working Position of Tool
The tool can be turned every 30 degrees and can
be fixed at the position of 12 steps.
(1) As shown in Fig. 3, if the grip (A) is turned in the
direction of B in a state where the grip (B) is turned
60 degrees in the direction of A, the blade angle
can be changed freely to any desired position.
(2) As shown in Fig. 4, if the grip (B) is turned 60
degrees in the direction of A, the holding part of
the tool automatically turns 30 degrees. If this action
is repeated, the blade angle of the tool can be
changed by every 30 degrees.
(3) Release grip (B) and turn the tool, and make sure
that it is locked completely.
6. Removing Tool
As shown in Fig. 1, pull grip (A), and pull out the
tool in a state where it is further turned in the
direction of B.
HOW TO USE THE HAMMER (Fig. 5)
1. After placing the tip of the tool in the base hole,
switch ON.
2. By utilizing the weight of the machine and by firmly
holding the hammer with both hands, one can
effectively control the subsequent recoil motion.
Proceed at a moderate work-rate, the use of too
much force will impair efficiency.
GREASE REPLACEMENT
This machine is of full air-tight construction to protect
against dust and to prevent lubricant leakage. This
machine can be used without grease supplement for an
extended period of time. However, perform the grease
replacement to maintain the service life. Replace the
grease as described below.
1. Grease Replacement Period
You should look at the grease when you change
the carbon brush. (See item 4 in the section
MAINTENANCE AND INSPECTION.) Ask for grease
replacement at the nearest authorized Hitachi Service
Center.
In the case that you are forced to change the grease
by yourself, please follow the following points.
2. How to replace grease
CAUTION:
Before replacing the grease, turn the power off and
pull out the plug from the receptacle.
(1) Remove the crank cover and wipe off the old grease
inside. (Fig. 6)
(2) Supply 30 g (the standard volume to cover the
connecting rod) of Hitachi Electric Hammer Grease
A to the crank case.
(3) After replacing the grease, install the crank cover
securely.
NOTE:
The Hitachi Electric Hammer Grease A is of the low
viscosity type. When the grease is consumed,
purchase from an authorized Hitachi Service
Center.

MAINTENANCE AND INSPECTION

1. Inspecting the tool
Since use of a dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
4. Inspecting the carbon brushes (Fig. 7)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or
near the "wear limit", it could result in motor
trouble. When an auto-stop carbon brush is
equipped, the motor will stop automatically. At
that time, replace both carbon brushes with new
ones which have the same carbon brush Numbers
shown in the figure. In addition, always keep carbon
brushes clean and ensure that they slide freely
within the brush holders.
5. Replacing carbon brushes:
Loosen the set screw and remove the tail cover.
Remove the brush caps and carbon brushes. After
replacing the carbon brushes, do not forget to
tighten the brush caps securely and to install the
tail cover.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATION
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HITACHI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
English
5