Eaton PowerXL DG1 Serie Instrucciones De Montaje página 18

Instruction Leaflet IL040016EN
Effective March 2014
Factory-Set Control Terminal Functions
I/O Connection
Pin Signal Name Signal
1 +10V
2 AI1+
3 AI1–
4 AI2+
i
5 AI2–
6 GND
7 DIN5
8 DIN6
9 DIN7
10 DIN8
11 CMB
12 GND
13 24V
14 DO1
15 24Vo
16 GND
17 AO1+
18 AO2+
19 24Vi
20 DIN1
21 DIN2
22 DIN3
23 DIN4
24 CMA
25 A
26 B
27 R3NO
28 R1NC
29 R1CM
30 R1NO
31 R3CM
32 R2NC
33 R2CM
34 R2NO
EATON
18 www.eaton.com
SW1
AI1 0–10V
AI2 0–20 mA
AI2 SW1
AI2 SW2
SW2
On
(RS-485 matching resistor)
Off
Ref. Output Voltage
Analog Input 1
Analog Input 1 Ground
Analog Input 2
Analog Input 2 Ground
I/O Signal Ground
Digital Input 5
Digital Input 6
Digital Input 7
Digital Input 8
DI5 to DI8 Common
I/O Signal Ground
+24 Vdc Output
Digital Output 1
+24 Vdc Output
I/O Signal Ground
Analog Output 1
Analog Output 2
+24 Vdc Input
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
DI1 to DI4 Common
RS-485 Signal A
RS-485 Signal B
Relay 3 Normally Open
Relay 1 Normally Closed
Relay 1 Common
Relay 1 Normally Open
Relay 3 Common
Relay 2 Normally Closed
Relay 2 Common
Relay 2 Normally Open
AI2 0–20 mA AI2 0–10V
Default Setting Description
— 10 Vdc Supply Source
0–10V Voltage Speed Reference (Programmable to 4 mA to 20 mA)
— Analog Input 1 Common (Ground)
4 mA to 20 mA Current Speed Reference (Programmable to 0–10V)
— Analog Input 2 Common (Ground)
— I/O Ground for Reference and Control
Preset Speed B0 Sets frequency output to Preset Speed 1
Preset Speed B1 Sets frequency output to Preset Speed 2
Emergency Stop (T–) Input forces VFD output to shut off
Force Remote (T+) Input takes VFD from Local to Remote
Grounded Allows source input
— I/O Ground for Reference and Control
— Control voltage output (100 mA max.)
Ready Shows the drive is ready to run
— Control voltage output (100 mA max.)
— I/O Ground for Reference and Control
Output Frequency Shows Output frequency to motor 0–60 Hz (4 mA to 20 mA)
Motor Current Shows Motor current of motor 0–FLA (4 mA to 20 mA)
— External control voltage input
Run Forward Input starts drive in forward direction (start enable)
Run Reverse Input starts drive in reverse direction (start enable)
External Fault Input causes drive to fault
Fault Reset Input resets active faults
Grounded Allows source input
— Fieldbus Communication (Modbus, BACnet)
— Fieldbus Communication (Modbus, BACnet)
At Speed Relay output 3 shows VFD is at Ref. Frequency
Run Relay output 1 shows VFD is in a run state
At Speed Relay output 3 shows VFD is at Ref. Frequency
Fault Relay output 2 shows VFD is in a fault state
PowerXL DG1 Series VFD
AI2 10–10V