Tabla de contenido
Idiomas disponibles
Idiomas disponibles
The f ollowing
guide bar a nd c hain combina-
tions m eet kickback
requirements
ofCSA
Z62.1, Z62.3, &ANSi B175.1
when used on
saws listed inthis manual.
Use o fbar and
Computed
kickback
angle
(CKA)
Table
I
_BA
MOOEL
P/N I ' thl
PP4820AVHD
545049801
I
20"
I
NOTE:
Ifthis saw is to be used for cemmer-
eial legging,
a chain
brake
is required
and
shall net be removed
or otherwise
disabled
to compty
with Federal
OSHA
Regulations
for Cemmereial
Legging.
SAFETY
NOTICE:
Exposure
to vibrations
through
prolonged
use of gasoline powered
hand tools couM cause blood vessel or nerve
damage
in the fingers,
hands, and joints of
people
prone
to
circulation
disorders
or
abnormal
swellings.
Prolonged
use
in cold
weather
has
been
linked
to blood
vessel
damage
in
otherwise
healthy
people.
If
symptoms
occur
such
as numbness,
pain,
loss of strength, change in skin color or texture,
or toss of feeling in the fingers, hands, or joints,
discontinue
the use
of this tool
and seek
medical
attention.
An anti-vibration
system
does not guarantee
the avoidance
of these
problems.
Users who operate power tools on
a continual
and regular
basis must monitor
closely
their
physical
condition
and
the
condition of this tool
SPECIAL
NOTICE:
Your saw is equipped
with a temperature
limiting muffler and spark
arresting
screen
which
meets
the
requirements
of California
Codes 4442 and
chain combinations
other than those listed is
not recommended
and may not meet the
CKA requirements
per standard.
CHAIN P/N
CKA without
chain
brake
952051310
31 °
4443.
All U.S. forest land and the states of
California,
Idaho,
Maine,
Minnesota,
New
Jersey, Oregon,
and Washington
require by
law that many internal
combustion
engines
to be equipped
with a spark arresting screen.
if you operate a chain saw in a state or locale
where such regulations
exist, you are legatly
responsible
for maintaining
the operating
condition
of these parts.
Failure to do so is
a violation of the law. Refer to the SERVICE
section
for
maintenance
of
the
spark
arresting
screen.
Failure to follow ail Safety Rules and Precau-
tions can result in serious
injury. If situations
occur which are not covered
in this manual,
use care and good judgement,
if you need
assistance,
contact your authorized
service
dealer or call 1-800-554-6723.
STANDARDS:
This saw is listed by Under-
writer's Laboratories,
inc., in accordance with:
ANSI
B175.1-2000
American
National
Standards
for
Gasoline-Powered
Chain
Saws - Safety Requirements
CSA
Z62.1=1995
Chain
Saws
- Occupa-
tional Health and Safety
CSA Z62.3-1996
Chain Saw Kickback
Oc-
cupational
Health and Safety
A
4t_ WARNING:
if received assembled,
repeat all steps to ensure your saw is properly
assembled
and all fasteners
are secure.
Al-
ways
wear protective
gloves
(not included)
when handling the chain. The chain is sharp
and can cut you even when it is not moving!
ATTACHING
THE
BUMPER
SPIKE
The bumper
spike may be used as a pivot
when making a cut.
1.
Loosen and remove the chain brake nuts
and the chain brake from the saw.
2.
Attach
the bumper
spike with
the two
screws
as illustrated.
ATTACHING
TH E BAR & CHAIN
(if not
already
attached)
1.
Loosen and remove the chain brake nuts
and the chain brake from the saw.
2.
Remove
the plastic
shipping
spacer
(if
present).
Location
of shipping
spacer
a_
Chain
Braj_e
Ch
Nuts
Bar Tool
3.
An adjusting pin and screw is used to ad-
just the tension of the chain, it is very im-
portant when assembling
the bar, that the
pin located on the adjusting screw aligns
into a hoie in the bar. Turning the screw will
move the edjustment
pin up and down the
screw. Locate this adjustment
before you
begin mounting the bar onto the saw. See
illustration below.
Tabla de contenido
