Chicco KEY1 ISOFIX Instrucciones De Uso página 37

6. Insert the two ISOFIX connectors into the
corresponding ISOFIX locking devices, lo-
cated on the car seat, between the backrest
and the seat (diag. 13). WARNING! Ensure
that the two ISOFIX connectors are locked
correctly into position, checking that the
two (Z) signs are green.
7. Push the child car seat firmly against the
backrest of the car seat (diag. 14) to ensure
maximum adherence.
HOW TO FIT THE TOP TETHER
The installation of the child car seat is com-
plete only by fitting the Top Tether.
WARNING! Pease refer to the instructions
booklet of the vehicle to identify the locking
point of the Top Tether of the child car seat.
This locking point is marked by a specific label
(diag. 15), and it may be located in the po-
sitions indicated in the diagrams 16a – 16b
– 16c – 16d – 16e.
WARNING! Check that the Top Tether is
locked with the correct locking device. Do not
mistake the locking device of the Top Tether
with the ring provided for securing the luggage
(diag. 17).
WARNING! Insert the Top Tether between the
top part of the backrest of the car seat and the
headrest. Never insert the Top Tether above
the headrest (diag. 18).
8. After identifying the locking point, connect
the hook (DD) of the Top Tether (diag. 19).
9. Adjust the length of the Top Tether belt,
pulling the strap firmly to tension it cor-
rectly (diag. 20). The belt is tensioned cor-
rectly when the indicator located on the
strap is green (diag. 21).
10. Roll up the excess strap and fix it with the
specific Velcro strap provided (diag. 22).
HOW TO REMOVE THE ISOFIX SYSTEM
WARNING! Remove the child from the child
car seat before proceeding to the removal of
the ISOFIX system.
1. Loosen the Top Tether by pressing the ap-
propriate button BB (diag. 23), then release
the hook.
2. Roll up the Top Tether strap and fix it with
the appropriate Velcro strap (diag. 22).
3. Pull the unlocking handle of the ISOFIX
system externally (L) and, while keeping it
pulled, detach the child car seat from the
backrest of the car seat, until the ISOFIX
system is removed completely (diagrams
24a-24b).
4. Push the two red buttons inside and relea-
se the connectors from the corresponding
ISOFIX locking devices, located on the car
seat (diag. 25).
5. Remove from the base of the child car seat
the two caps stored in advance, and rein-
sert them in the related ISOFIX connectors,
paying attention that the two ends are fa-
cing inside (diagrams 26a-26b).
6. Push the ISOFIX system inside the base of
the child car seat, inserting it completely
into the base (diag. 27).
FITTING THE CHILD SEAT INTO THE CAR
WITH A 3-POINT SAFETY BELT
WARNING! NEVER USE THE CAR SAFETY BELT
IN ANY OTHER POSITIONS THAN THOSE IN-
DICATED IN THIS INSTRUCTION BOOKLET: IT
COULD COMPROMISE THE CHILD'S SAFETY!
The holes to insert the safety belts are high-
lighted on the child car seat with red signs.
WARNING! These instructions and diagrams
are for the installation of the child car seat on
the right back seat. To fit the child car seat in
other positions, carry out these operations in
the same order.
1. Place the child car seat on the desired
car seat. WARNING! Ensure there are no
objects placed between the child car seat
and the car seat, or the child car seat and
car door.
2. Recline the backrest of the child car seat
fully, pulling the lever located under the
seat in your direction (Q) (Diag. 28).
3. Pull the car safety belt, sliding it in the spa-
ce between the backrest and the base of
the child car seat (Diag. 29).
4. Insert the lap section of the 3-point car
safety belt into the corresponding safety
belt guides (Diag. 30).
5. Pull out the safety belt from the other side
of the child car seat, and fasten it to the
seat buckle (Diag. 31).
6. Open the safety belt locking clamp (T), lo-
cated on the same side of the seat buckle,
by pressing the lever (diag. 32).
7. Insert the diagonal section of the car safety
belt into the clamp, and place the diagonal
section as shown in diag. 33. When relea-
sed, the clamp lever will automatically re-
turn to the locked position.
8. Pull the diagonal section of the car safety
belt firmly, ensuring that the child car seat
adheres correctly to the car seat (diag. 34).
If necessary, carry out this operation exer-
cising some pressure on the child car seat
with your knee.
37