Cleaning And Storage; Power Cord Maintenance; Troubleshooting; Waste Disposal And Environmental Protection - IKRA HLSI 260 Instrucciones De Manejo

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 45
above the ground swing the machine from side to side,
moving forwards and directing the nozzle at the debris to
be collected. Do not force the nozzle into the debris as
this will block the suction tube and reduce the efficiency
of the machine.
Organic materials such as leaves contain a large amount
of water that can cause them to stick to the inside of the
suction tube. To reduce sticking the material should be
left for a few days to dry out.

Cleaning and Storage

Make sure that all nuts, bolts and screws are tight and
that the guards are fitted correctly.
All damaged and worn parts should be replaced in
order to maintain the Vacuum-Blower in a safe working
condition.
Never leave material in the Vacuum-Blower or the debris
collection bag. This could be dangerous when starting
the Vacuum-Blower.
After use the Vacuum-Blower should be thoroughly
cleaned.
Ensure that the Vacuum-Blower is switched off and dis-
connected from the mains supply. Remove and empty
the debris collection bag. Ensure that the Vacuum /
Blow selector lever operates smoothly and that it is not
obstructed by debris. Brush any loose debris from around
the fan and inside the suction/blower tube.
Do not use any type of cleaning solvent on the plastic
parts of the Vacuum-Blower.

Power Cord Maintenance

If the supply cord needs replacing, the task must be car-
ried out by the manufacturer, the manufacturer's agent,
or an authorised service centre in order to avoid a safety
hazard.

Troubleshooting

Attention! Always remove the plug from the
mains socket before starting any work on the
machine.
The machine won't start: Check whether the switch
is in the "ON" position; check that the residual current
circuit breaker is not switched off and that no fuses
have blown in its electric circuit. If the machine still
won't start have it inspected by an authorised cus-
tomer service firm.
The machine won't vacuum: Check whether the
leaf collection bag is full. If it is, empty it; check
whether the lever for the reversing flap is in the cor-
rect position, otherwise have the machine inspected
by an authorised customer service firm.
The machine won't blow: Check whether the lever
for the reversing flap is in the correct position, other-
wise have the machine inspected by an authorised
customer service firm.
GBR | Operating Instruction

Waste disposal and environmental protection

If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
of the device together with your domestic refuse, but dis-
pose of it in an environmentally friendly manner. Please
dispose of the device itself at an according collecting/
recycling point. By doing so, plastic and metal parts can
be separated and recycled. Information concerning the
disposal of materials and devices are available from your
local administration.

Repair service

Repairs to electric power tools should only be carried
out by specialist electrical personel. In the case of a
claim for guarantee or defects, please contact the place
of purchase.

Warranty

For this tool, the company provides the end user - inde-
pendently from the retailer's obligations resulting from
the purchasing contract - with the following warranties:
The warranty period is 24 months beginning from the
hand-over of the device which has to be proved by the
original purchasing document. For commercial use and
use for rent, the warranty period is reduced to 12 months.
Wearing parts and defects caused by the use of non
fitting accessories, repair with parts that are not original
parts of the manufacturer, use of force, strokes and
breaking as well as mischievous overloading of the motor
are excluded from this warranty. Warranty replacement
does only include defective parts, not complete devices.
Warranty repair shall exclusively be carried out by au-
thorized service partners or by the company's customer
service. In the case of any intervention of not authorized
personnel, the warranty will be held void.
All postage or delivery costs as well as any other subse-
quent expenses will be borne by the customer.

Spare parts

Collection bag
GBR-6
The shredder wheel is blocked: Check whether an
object has been sucked in that is too large; a piece of
wood, cardboard or other object has become jammed
between the impeller and shredder chamber. If the
shredder wheel remains blocked have the machine
inspected by an authorised customer service firm.
If the machine vibrates, please immediately stop us-
ing it. Have the machine inspected by an authorised
customer service firm.
# 74200020
Tabla de contenido
loading

Tabla de contenido