General Maintenance - EGO BC3800E Manual De Uso

Tabla de contenido

Idiomas disponibles

1. Remove the battery pack.

2. Remove the remaining cutting line, if necessary.

3. Rotate the spool retainer in the direction indicated by the

arrow, as necessary, to align the LOAD line on the spool

retainer with the eyelets in the spool base (Fig. W-1).

4. Cut 5m of cutting line, and insert the line into the

mounting hole inside the eyelet (Fig. W-2). Push and

pull the line from the other side until equal amounts

of line appear on both sides of the spool (Fig. W-3).

5. Press, while rotating the spool retainer in the arrow

direction, to wind the line onto the spool until

approximately 14cm of line is showing on each side

(Fig. W-4).

6. Push the spool retainer down while pulling on the

lines to manually advance the line and to check for

proper assembly of the trimmer head.

When the cutting line breaks from the line outlet or the

cutting line is not released when tapping the trimmer

head, follow the steps below:

1. Remove the battery pack.

2. Press the release tabs on the spool retainer and

remove the spool retainer by pulling it straight out

(Fig. H-1 & H-2).

3. Remove the cutting line from the spool retainer.

4. With one hand holding the spool base, use the other

hand to grasp the spool retainer and align the tabs

on the spool retainer with the holes in the spool base

(Fig. X-1); use your palm to press and rotate the

spool retainer left and right until the tabs lock with

the spool base (Fig. X-2).

5. Reload the cutting line.

USING WITH 3-TEETH METAL

WARNING:

To cut wild growth and scrub, lower the

rotating 3-teeth blade down onto the growth to achieve a

chopping effect. Use the brush cutter like a scythe (sweep

it to the right and left) at ground level. Do not use the

cutting unit above waist height.

WARNING:

The higher the cutting unit is off the

ground, the greater the risk of injury from cuttings being

thrown sideways.

WARNING:

When cutting young stands or other

woody materials up to 2cm in diameter, use the left

side of the blade to avoid blade thrust situations. Do not

attempt to cut woody material with a larger diameter,

since the blade may catch or jerk the brush cutter

forward. This may cause damage to the blade or the

brush cutter or loss of control of the brush cutter, resulting

personal injury.

56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUCHCUTTER — BC3800E

WARNING:

Improper use of a blade may cause it to

crack, chip, or shatter. Thrown parts may seriously injure

the operator or bystander. To reduce the risk of personal

injury, it is essential to take the following precautions:

◾

Avoid contact with hard or solid foreign objects such as

stones, rocks or pieces of metal.

◾

Never cut wood or shrubs with a stem diameter of

more than 2cm.

◾

Inspect the blade at a regular short interval for signs of

damage. Do not continue working with a damaged blade.

◾

Re-sharpen the blade regularly (when it has dulled

noticeably) and have it balanced if necessary

(performed by a qualified service technician).

Blade Thrust

Exercise extreme caution when using the 3-teeth blade

with this unit. Blade thrust is the reaction that may occur

when the spinning blade contacts anything it cannot cut.

This contact may cause the blade to stop for an instant

and suddenly "thrust" the unit away from the object that

was hit. This reaction can be violent enough to cause the

operator to lose control of the unit. Blade thrust can occur

without warning if the blade snags, stalls, or binds. This is

more likely to occur in areas where it is difficult to see the

material being cut. For cutting ease and safety, approach

the weeds being cut with the brush cutter from the right

to the left. In the event an unexpected object or woody

stock is encountered, this practice could minimize the

blade thrust reaction.

MAINTENANCE

WARNING:

Before inspecting, cleaning or servicing

the unit, stop the motor, wait for all moving parts to stop,

and remove the battery pack. Failure to follow these

instructions can result in serious personal injury or

property damage.

WARNING:

When servicing, use only identical

replacement parts. Use of any other parts may create a

hazard or cause product damage. To ensure safety and

reliability, all repairs should be performed by a qualified

service technician.