EGO BC3800E Manual De Uso página 11

◾
If you are approached, stop the motor and cutting unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade.
A dull blade is more likely to snag and thrust (only
using with 3-teeth blade).
◾
The battery pack shall be disposed of safely.
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Do not charge the battery pack in rain, or in wet
locations.
◾
Use only with EGO's battery packs and chargers listed
below:
BATTERY PACK
BA1120E, BAX1300, BA2240E,
BA2800, BA3360, BA4200
◾
The battery pack must be removed from the
appliance before it is scrapped.
◾
Do not dispose of the battery in a fire. The cells may
explode. Check with local codes for possible special
disposal instructions.
◾
Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
◾
Exercise care in handling batteries in order not
to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.
◾
Replacement parts - When servicing, use only
identical EGO replacement parts. Use of any other
accessory or attachment may increase the risk of injury.
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUCHCUTTER — BC3800E
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Remove or disconnect battery pack before
servicing, cleaning or removing material from the
brush cutter.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Cutting unit
Voltage
No-load Speed
Cutting Line Type
Cutting blade
Cutting Width
Weight (without battery
pack)
Measured sound
power level L
CHARGER
Sound pressure level at
operator's position L
CH2100E
Guaranteed sound
CH5500E
power level L
(measured according
to 2000/14/EC)
Valuation of
vibration a
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE:
power tool can differ from the declared value in which the
tool is used; In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.
Trimmer head
56 V
4500-6000 /min 4500-6000 /min
2.4mm nylon
twist line
/
38 cm
4.35 kg
94.80 dB(A)
K=1.01 dB(A)
WA
80.2 dB(A)
K=2.5 dB(A)
PA
96 dB(A)
WA
Left 2.28 m/s
2
handle K=1.5 m/s
2
Right 2.38 m/s
2
h
handle K=1.5 m/s
2
The vibration emission during actual use of the
EN
3-teeth metal
blade
56 V
/
ABB1203
30 cm
4.64 kg
94.04 dB(A)
K=1.71 dB(A
80.0 dB(A)
K=4.1 dB(A)
96 dB(A)
1.55 m/s
2
K=1.5 m/s
2
1.88 m/s
2
K=1.5 m/s
2
11