Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Fig. G
1
Variable Speed Trigger (Fig. H)
In addition to the variable speed dial, the material's rate of
flow is also controlled with a variable speed trigger.
1. Squeeze the trigger switch
nOTE: The further the trigger is depressed the faster the
rate of flow.
2. Release the trigger switch to turn the tool off.
Fig. H
1
Trigger Switch Lock-off (Fig. H)
Your tool is equipped with a trigger switch lock-off
safeguard against inadvertent release of material.
1. To lock the trigger switch, push trigger switch lock-
off
2
up. The tool will not operate with the switch in
the locked position.
2. To unlock the trigger switch, push the trigger switch
lock-off down.
Rotating Cartridge Holder (Fig. I)
The cartridge holder
8
rotates 360˚ to apply material at
any angle.
Fig. I
8
Plunger Rod Handle (Fig. A)
WARNING: To reduce the risk of serious personal
injury, DO NOT use the plunger rod handle as a hook
to suspend objects from.
The plunger rod handle
may be used to suspend tool
4
from a stable location when not in use or for storage.
3
1
to turn the tool on.
2
2
to
9
To Adjust Plunger Rod (Fig. A)
1. To manually adjust plunger rod
plunger rod release trigger
2. Push or pull plunger rod handle
3. Release plunger rod release trigger.
To Insert Material
Cartridge Holder (Fig. A, K)
1. Ensure that the proper cartridge holder
installed properly.
2. Use the trigger switch lock-off
switch
.
1
3. Trim nozzle end of the caulk/adhesive tube (Fig. K).
Small openings require more force to push the material
possibly affecting battery life.
4. Break inner seal of caulking tube or adhesive material
using the poker
9
located on the under side of the
cartridge holder.
NOTICE: If the inner seal is not broken, material could be
forced out through the rear of the tube and damage the tool.
NOTICE: Keep plunger rod, cartridge holder and cartridge
clean of all material. Retracting a plunger rod that is covered
with dried material may damage the internal parts of the tool
and cause misalignment of tube.
5. Securely hold the tool, press plunger rod release
trigger
to declutch and free the plunger rod
6
Using the plunger rod handle
back to allow the caulk/adhesive tube to fit inside the
cartridge holder.
6. Insert caulk/adhesive tube.
7. Press and hold plunger rod release trigger
pushing the plunger rod handle
plunger
is against the tube.
7
8. Release the plunger rod release trigger.
9. Rotate cartridge holder to desired angle.
Sausage Holder (Fig. A, J, K)
1. Unscrew and remove nozzle cap
2. Press and hold plunger rod release trigger
the plunger rod handle
4
to allow the caulk/adhesive casing to fit inside the
sausage holder
12
.
3. Insert sausage pack into sausage holder and cut casing
(closest end to the nozzle) according to adhesive
manufacturer's instructions.
iMPORTAnT: This sausage holder is designed to be
used only WiTh sausage packs. DO nOT remove caulk/
adhesive material from the casing. nEVER dip the
nozzle tip into any type of material.
Fig. J
12
4. With nozzle tip facing away from tool, screw nozzle cap
back onto sausage holder.
English
, press and hold the
5
.
6
to desirable position.
4
8
is
2
to lock trigger
.
5
, pull the plunger rod
4
6
while
forward until the
4
13
. and nozzle.
. Using
6
, pull plunger rod
back
5
13
9
Tabla de contenido
