Care And Maintenance - Bushnell StealthView 26-0542 Manual De Instrucciones

6. To focus the image, first adjust the eyepiece diopter (9) and then rotate the objective lens (1) until the display screen is in focus
and the view is clearest. At this point, the eyepiece diopter is set for your individual eyesight and will not require further
adjustment when viewing objects at different distances. When changing the viewing distance, simply rotate the objective
lens (1) until the image is in focus.
7. To adjust the image brightness of the viewing screen, either press the "+" (6) to increase brightness or the "-"(7) to decrease
brightness. If the device is turned off and then back on, the brightness level will return to the previous brightness level.
8. When you power the device on, the short range Infrared Illuminator (13) is automatically turned on.
9. StealthView Digital Night Vision also contains a "super" infrared (I.R.) diode (14) for illumination of objects in complete
darkness where no ambient light source, such as moonlight, is available. To activate the super IR, simply press the IR button
(10) located next to the ON button. If the device is focused on an object closer than 15 yards / meters, the emission spot
of this "super" infrared (bright light circle) will be shifted to the right side of the display. While focusing from one object to
another object, it might be necessary to rotate the objective lens and increase or decrease image brightness of the viewing
screen in order to achieve the best image quality.
10. The StealthView contains a video output port (11). This port allows one to transmit images to an external LCD monitor or
video recorder. Plug the output video cable into the StealthView video output port (11). When the StealthView is coupled
with video equipment, the observed image can be recorded.
11. The StealthView also contains a 12 volt auxiliary power port (12). To connect the StealthView to this port, plug the power
cable (not included) into the StealthView's power input port and connect the other end of the cable to the vehicle's auxiliary
power port. To connect the StealthView to a household outlet, use a 12 volt dc output switching power adapter (not
included).
NOTE: When the batteries are in the battery cartridge and the external power source is turned on, the device operates on the
external power source. If you unplug the external power source, and you want to use the battery source, you have to press
the ON button (3) to make the device operate.
4
TROUBLESHOOTING
StealthView will not turn on
1. Check that the batteries and battery cartridge (2) are installed correctly. If the batteries and cartridge are installed correctly
and the batteries are good, then the green LED indicator light should be on.
2. Check that the power button (3) has been depressed to the ON position.
Image is not focused.
1. Adjust the focus of the objective lens (1) and eyepiece diopter (9).
2. Adjust the LCD brightness screen up or down until satisfactory.
3. Try turning the super I.R. spotlight ON (10). Typically, the super I.R spotlight needs to be on when viewing objects far away
in complete darkness and can be off when viewing objects at close distances with some ambient light.

CARE AND MAINTENANCE

Your Bushnell Digital Night Vision device was designed to provide many years of reliable service. To ensure that you get the
most enjoyment out of your Digital Night Vision device, always obey the following warning and precautions.
• Do not open the body of the device or otherwise attempt to service this device.
• Always store the device in a dry, well ventilated room.
• Keep the device away from any heating and air conditioning vents or other heating devices, direct sunlight, and moisture.
• Avoid dropping or otherwise shocking the unit. Although designed for rugged outdoor use, this device incorporates a
sophisticated digital circuitry which could be damaged in extreme cases of misuse.
• Clean the optical lens with a professional lens cleaning supplies.
• Clean the exterior of the device with a soft clean cloth.
• Avoid removing the objective lens as the CMOS chip can be damaged.
• Do not leave the device in direct sunlight or rain.
• Do not cover the vent grid (8) of the super I.R.
• The device can be powered with 6 nickel cadmium batteries or 6 alkaline batteries.
• The super I.R. is focused correctly from the factory. Do not attempt to adjust the focus of the super I.R.
• Remove the batteries if the device will not be used for longer than 2 months.
5