Makita BHL360 Manual De Instrucciones página 8

Battery remaining capacity indicator (only for
models with Battery BL3622A) (Fig. 2)
Battery BL3622A is equipped with the battery remaining
capacity indicator.
Press the CHECK button to indicate the battery remain-
ing capacity. The indicator lamps will then light for
approx. three seconds.
Indicator lamps
Lighted Off Blinking
E
011713
• When only the lowermost indicator lamp (next to the
"E") blinks, or when none of the indicator lamps light,
the battery capacity has run out, so the tool does not
operate. In these cases, charge the battery or replace
the empty battery with a fully charged one.
• When two or more indicator lamps do not light even
after charging is complete, the battery has reached the
end of its service life.
• When the upper two and lower two indicator lamps light
alternately, the battery may have malfunctioned. Con-
tact your local Makita authorized service center.
NOTE:
• The indicated capacity may be lower than the actual
level during use or immediately after using the tool.
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the
actual capacity.
Power switch action (Fig. 3)
WARNING:
• Before inserting the battery cartridge in the tool,
always check to see that the switch actuates prop-
erly. Operating a tool with a switch that does not actu-
ate properly can lead to loss of control and serious
personal injury.
To turn on the tool, press the switch to "I" (ON) side. The
carbon rods gradually start vibrating, and the tool
reaches its top speed in a few seconds.
To turn off the tool, press the switch to "O" (OFF) side.
Unintentional restart proof
When the battery cartridge is inserted on the tool with the
switch in the "I (ON)" side, the tool does not start. At this
time, the unintentional restart proof device is on function.
To start the tool, first press the switch to the "O (OFF)"
side and then press it to the "I (ON)" side.
8
Remaining capacity
70% to 100%
F
45% to 70%
20% to 45%
0% to 20%
Charge the battery.
The battery may have
malfunctioned.
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool. Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
• Never start the tool unless it is completely assem- bled. Operation of the tool in a partially assembled
state may result in serious personal injury from acci-
dental start-up.
• Always hold the telescopic rod with both hands when
operating with the telescopic rod. Operating the tele-
scopic rod with one hand may lead to lose control and
result in personal injury.
• Before use, make sure that the carbon rods are
inserted all the way in the connecting rod and attached
firmly.
• Do not point the harvester at persons.
Installing the carbon rod (Fig. 4)
Put the carbon rods through the rod holder. Set the end
of the carbon rods along the retainer. And then set them
into the connecting rod. Make sure the ends of the all
carbon rods reach at the bottom of the connecting rod.
And then tighten firmly the bolt by hex wrench to attach
the retainer to the connecting rod.
NOTE:
• The rod holder always comes approximately 50 to
60 mm from the connecting rod when the carbon rods
is attached properly.
Installing the power cable (directly to the
harvester) (Fig. 5)
Loosen ring nut counterclockwise. Insert the power cable
in the hole of the harvester. Tighten the ring nut clock-
wise. Make sure the power cable is attached firmly.
To remove the power cable, loosen the ring nut counter-
clockwise, and pull it out from the harvester.
Installing the power cable (when using telescopic
rod) (Fig. 6 & 7)
Loosen ring nut counterclockwise. Insert the telescopic
rod in the hole of the harvester. Tighten the ring nut
clockwise. Make sure the telescopic rod is attached
firmly.
Insert the power cable in the hole of the telescopic rod
until a little click is felt. Make sure the power cable is
firmly attached.
Telescopic rod adjustment (Fig. 8)
Hold the lower part of the telescopic rod firmly with one
hand. Turn the upper part of the telescopic rod to unlock
it. Expand the telescopic rod to desired length. Tighten
the upper part of the telescopic rod by turning it again.