Alesis MULTIMIX 16 USB FX Guia Del Usuario página 8

15. GUITAR SWITCH – When this switch is in the down position,
Channel 8 will serve as a high-impedance input for connecting guitar
or bass instruments. When the switch is in the up position, Channel
8 will accept mic or line-level signals.
16. GAIN – Adjusts the channel audio level (pre-fader and pre-EQ gain).
Adjust this so that the PEAK LED just barely lights up during the
loudest parts of the song.
17. CHANNEL VOLUME – Adjusts the audio level on the channel.
18. MUTE – When this button is engaged, the channel's audio will be
muted.
19. SOLO – When this button is engaged, the channel's audio will be
sent to the MONITOR OUT and PHONES outputs. (This function
will still work even when the channel is muted.)
20. PEAK LED – The LED will flash red if the signal is clipping. If this
happens, decrease the setting of the GAIN knob or CHANNEL
VOLUME knob.
21. CHANNEL PAN – Adjusts the (mono) channel's position in the
stereo field.
22. BALANCE (CH 9-16) – Adjusts the balance between
Channels 9-16.
23. LO EQ (BASS) – Adjusts the low (bass) frequencies of the
channel.
24. MID EQ – Adjusts the mid-range frequencies of the
channel.
25. MID EQ FREQ – Adjusts the frequency that the CHANNEL
EQ (MID) will boost or cut.
26. HI EQ (TREBLE) – Adjusts the high (treble) frequencies of
the channel.
27. AUX PRE SEND – Adjusts the channel audio (pre-EQ) level that is sent to the AUX SEND output. You can
use this to apply external effects to individual channels, or to create a custom monitor mix for yourself or your
musicians.
28. FX SEND – Adjusts the channel audio level that is sent to MultiMix 16 USB FX's internal effects processor.
Turn this up for the channels that you want internal effects applied to.
29. PREFADE – When this button is engaged, the FX Send signal can be controlled pre-fader.
30. EFFECTS SELECTOR – Selects the effect that MultiMix 16 USB FX's internal effects processor will apply to
the various channels. Each channel can send different levels of audio to the processor by adjusting their FX
POST SEND knobs. See the EFFECTS section for an explanation of the available effects.
31. AUX RETURN LEVEL – Adjusts the volume of the AUX RETURN INPUTS.
32. FX RETURN LEVEL – Adjusts the volume of the MultiMix 16 USB FX's internal effects processor.
33. LED METERS – Shows the audio level of the main mix. Turn the volume down if the CLIP LED lights up
excessively.
34. 2 TRKS/USB TO MAIN – Routes the audio from your computer and the 2 TRACK INPUTS to the MAIN OUT.
35. 2 TRKS/USB TO MONITOR – Routes the audio from your computer and the 2 TRACK INPUTS to the
MONITOR OUT and your headphones.
36. MAIN TO MONITOR – Routes the audio heard through the MAIN OUT to the MONITOR OUT and your
headphones.
37. MAIN VOLUME – Adjusts the volume of the MAIN OUT.
38. MONITOR VOLUME – Adjusts the volume of the MONITOR OUT.
39. PHONES VOLUME – Adjusts the volume to your headphones.
Use standard 1/4" TRS (tip-ring-
sleeve)
devices to the INSERT jacks.
signal is sent from the tip of the cable
and returns on the ring.
When recording to your computer,
make sure the 2 TRKS/USB TO MAIN
switch is in the up/raised position to
avoid feedback in your recording.
Alternately, you can deactivate the
"software playthrough" function in
your software while recording.
For software monitoring capability when
recording to your computer, make sure the
MAIN TO MONITOR switch is disabled and
the USB TO MONITOR switch is enabled.
Then connect
speakers to hear the signal.
8
cables when connecting
TRS (tip-ring-sleeve)
TS (tip-sleeve)
the Monitor outputs
The
to