Technical Data; Noise/Vibration Information - Bosch GMF 1400 CE Professional Manual Original

OBJ_BUCH-100-004.book Page 20 Wednesday, November 23, 2011 11:55 AM
20 | English
15 Guide plate
16 Mark on plunge base/non-plunge base
17 Tightening nut with collet
18 Router bit*
19 Chip shield (plunge base)
20 Clamping lever for plunge base/non-plunge base
21 Release lever for plunge action
22 Seat for parallel guide rods
23 Chip shield (non-plunge base)
24 Scale for depth-of-cut adjustment
(non-plunge base)
25 Adjustment knob for depth-of-cut fine adjustment
(non-plunge base)
26 Clamping lever for depth-of-cut coarse adjustment
(non-plunge base)
27 Coarse adjustment notches for non-plunge base
28 Mark on routing motor
29 Open-end spanner, size 16 mm
30 Open-end spanner, size 24 mm
31 Extraction hose (Ø 35 mm)*
32 Extraction adapter (plunge base)*
33 Knurled screw for extraction adapter (plunge base)
(2x)*
34 Fastening screw for extraction adapter
(non-plunge base) (2x)*
35 Extraction adapter (non-plunge base)*
36 Parallel guide*
37 Guide rod for parallel guide (2x)*
38 Wing bolt for fine adjustment of parallel guide (2x)*
39 Wing bolt for coarse adjustment of
parallel guide (2x)*
40 Fine-adjustment knob for parallel guide*
41 Adjustable edge guide for parallel guide *
42 Wing bolt for guide rods of parallel guide (2x)*
43 Router compass/guide-rail adapter*
44 Router compass handle*
45 Wing bolt for coarse adjustment of
router compass (2x)*
46 Wing bolt for fine adjustment of
router compass (1x)*

Noise/Vibration Information

Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are: Sound pressure level 86 dB(A); Sound power level 97 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined
h
according to EN 60745:
a
h
K
2 610 021 416 | (23.11.11)
47 Fine-adjustment knob for router compass*
48 Centring screw for compass stop *
49 Base spacer (included in the "router compass" set)*
50 Guide rail*
51 Fastening screw for guide bushing adapter (2x)
52 SDS guide-bushing adapter
53 Release lever for guide bushing adapter
54 Guide bushing
55 Fastening screw for guide plate
(plunge base: 3x, non-plunge base: 4x)
56 Centring pin
57 Specialty Allen key for depth-of-cut fine adjustment
(non-plunge base)*
58 Fastening screws for non-plunge base*
59 Extension for depth-of-cut fine adjustment
(non-plunge base)*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Multifunction Router
Article number
Rated power input
No-load speed
Speed preselection
Constant electronic control
Connection for dust extraction
Tool holder
Plunge depth (plunge base)
Weight according to
EPTA-Procedure 01/2003
– Contour router
– Plunge router
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Routing with
Non-plunge Base
2
m/s =6.5
2
m/s =2.0
GMF 1400 CE
Professional
3 601 F17 8..
W 1400
-1
min 8000 – 24000
mm 8 – 12
inch ¼ – ½
mm 59
kg 3.6
kg 4.1
/II
Routing with
Plunge Base
=5.5
=1.5
Bosch Power Tools