Starting Operation - Bosch GOF 900 CE Professional Manual Original

OBJ_BUCH-203-004.book Page 18 Wednesday, November 23, 2011 9:50 AM
18 | English
The machine can be plugged directly into the receptacle of a
Bosch all-purpose vacuum cleaner with remote starting con-
trol. The vacuum cleaner starts automatically when the ma-
chine is switched on.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Mounting the Chip Shield (see figure C)
Insert the chip shield 6 from the front into the guide in such a
manner that it engages. To remove the chip shield, grasp it by
the sides and pull it off toward the front.
Operation

Starting Operation

Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Preselecting the Speed
The required speed can be preselected with the thumbwheel
3 (also while running).
1 – 2 low speed
3 – 4 medium speed
5 – 6 high speed
The values shown in the chart are standard values. The neces-
sary speed depends on the material and the operating condi-
tions, and can be determined by practical testing.
Material
diameter (mm)
Hardwood (Beech)
Softwood (Pine)
Particle Board
Plastics
Aluminium
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.
Switching On and Off
Adjust the depth-of-cut before switching on or off; see Sec-
tion "Adjusting the Depth-of-cut".
To start the machine, press the On/Off switch 24 and keep it
pressed.
1 619 929 J79 | (23.11.11)
To lock the pressed On/Off switch 24, press the lock-on but-
ton 2.
To switch off the machine, release the On/Off switch 24 or
when it is locked with the lock-on button 2, briefly press the
On/Off switch 24 and then release it.
Constant Electronic Control
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perform-
ance.
Soft Starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
Adjusting the Depth-of-cut (see figure D)
The adjustment of the depth-of-cut may only be carried
out when the router is switched off.
For coarse adjustment of the depth-of-cut, proceed as follows:
– Place the machine with the router bit mounted on the
workpiece to be machined.
– Set the fine-adjustment path to the centre position with
the adjustment knob 20. For this, turn the adjustment
knob 20 until the marks 21 match as shown in the figure.
Afterwards, set the scale 19 to "0".
– Set the step buffer 10 to the lowest position; the step buff-
er engages noticeably.
– Loosen the wing bolt for the depth stop 14 so that the
Router bit Thumb-
depth stop 15 can be moved freely.
wheel 3
– Push the release lever 22 downward and slowly lower the
4 – 10 5 – 6
plunge router until the router bit 7 touches the surface of
12 – 20 3 – 4
the workpiece. Let go of the release lever 22 again to lock
22 – 40 1 – 2
this plunging depth.
4 – 10 5 – 6
– Push the depth stop 15 downward until it rests on the step
12 – 20 3 – 6
buffer 10. Set the slide with the index mark 16 to the "0"
22 – 40 1 – 3
position on the scale for the depth-of-cut adjustment 18.
4 – 10 3 – 6 – Set the depth stop 15 to the required depth-of-cut and
12 – 20 2 – 4 tighten the wing bolt for the depth stop 14. Pay attention
not to misadjust the slide with the index mark 16 again.
22 – 40 1 – 3
– Push the release lever 22 and guide the plunge router to
4 – 15 2 – 3
the uppermost position.
16 – 40 1 – 2
For deep cuts, it is recommended to carry out several cuts,
4 – 15 1 – 2
each with little material removal. By using the step buffer 10,
16 – 40 1
the cutting process can be divided into several steps. For this,
adjust the desired depth-of-cut with the lowest step of the
step buffer and select the higher steps first for the initial cuts.
The clearance of the steps can be changed by screwing the
adjusting screws 11 further in or out.
After a trial cut, the depth-of-cut can be set exactly to the de-
sired measure by turning the adjustment knob 20; turn in
clockwise direction to increase the cutting depth and in anti-
clockwise direction to decrease the cutting depth. The scale
19 can be used for guidance. One full turn corresponds with a
21
Bosch Power Tools