Control Panel - JB Systems Light iMove 7S Manual De Instrucciones

ENGLISH
HOW TO SET UP THE UNIT

CONTROL PANEL:

 DISPLAY shows the various menus and the selected functions.
 LEDS
DMX On DMX input present
MASTER On Master mode
SLAVE On Slave mode
SOUND Flashing Sound activation
 BUTTONS
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
 REMOTE CONTROL INPUT: Used to connect an optional CA-8 hand controller while the unit is used in
standalone or master/slave mode.
 SENSITIVITY: Used to adjust the sensitivity of the micro when the unit is used in standalone or
master/slave mode.
 MICROPHONE: used to trigger the internal programs to the rhythm of the music.
 DMX INPUT/OUTPUT: used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link
the units together.
MAIN MENU:
 To select any of the pre-set functions, press the MENU button up to when the required one is shown on
the display.
 Select the function with the ENTER button. The display will blink.
 Use DOWN and UP button to change the mode.
 Once the required mode has been selected, press the ENTER button to select. After 8 seconds the display
will automatically return to the main functions without any change. To go back to the functions without any
change press the MENU button. The main functions are shown on the right.
JB SYSTEMS®
OPERATION MANUAL
5/62 iMove 7S
ENGLISH
DMX512 Address Setting
Used to set the starting address in a DMX
setup.
 Press the MENU button until
is shown
on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to change the
DMX512 address.
 Once the correct address shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Show Mode
Used to choose the Show mode when used in
standalone or master/slave mode.
 Press the MENU button until
is showing
on the display.
 Press the ENTER button, the display starts
blinking.
 Use DOWN and UP buttons to select
(show 1), (show 2), (show 3) or
(show 4) mode.
 Once the right mode shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Show 1 mode- Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode-Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on a podium, in front of the audience
The spot is always projecting to the audience's direction; i.e in front of the stage. Pan movement
angel (left to right to left ): 160°. Tilt movement angel: 90° ( 60° above horizon; 30° below horizon.)
Show 4 mode - Fixture is fixed under ceiling.
The spot is mainly projecting in front of the stage. Pan movement angel ( left to right to left ) :160°.
Tilt movement angel: 90° ( vertically, front 75°; back 15° )
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(normal) or
 Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
JB SYSTEMS®
OPERATION MANUAL
(2 light show) mode.
6/62 iMove 7S