Important Safety Instructions For Charger & Battery - Makita 4603D Manual De Instrucciones

ENGLISH
1 Blade
2 Charging light
3 Start button
4 Charging plug
5 Charging connector
6 Shoulder strap
7 Adjusting strap
8 Waist belt
9 Female connector
10 Screw
11 Male plug
12 Battery
13 Screw
14 Lock-off button
SPECIFICATIONS
Model
Max. cutting capacity ......................... 25 mm in diameter
Strokes per minute .................................................... 100
Overall length ..................................................... 293 mm
Net weight ............................................................. 1.0 kg
Voltage .......................................................... D.C. 14.4 V
Charging time .............................................. Approx. 1 hr.
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
6
Explanation of general view
15 Switch trigger
16 Upper shear blade
17 Lower shear blade
18 Restart button
19 Restart button
20 Brush
21 Machine oil
22 Diamond file
23 Hex wrench
24 Loosen
25 Screw pin
26 Washer
27 Torsion spring
28 Cup washer
10. Do not disassemble charger or battery; take it to
4603D
11. To reduce risk of electric shock, unplug charger
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY
1.
2.
3.
4.
5.
6.
7.
8.
29 Hex lock nut
30 Block
31 Pull
32 Loosen
33 Holes for screws
34 Machine
35 Screw
36 Larger hole
37 Protrusion
38 Limit mark
39 Brush holder cap
40 Screwdriver
a qualified serviceman when service or repair is
required. Incorrect reassembly may result in a
risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
Charge battery only when room and battery case
temperature is between 10°C (50°F) and 40°C
(104°F). The battery cannot be charged when the
temperature is above 40°C (104°F). The battery
will be overcharged and its service life will be
shortened if you charge the battery when the
temperature is below 10°C (50°F).
Do not charge or leave battery in a location
exposed to direct sunlight.
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Do not short the battery:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery in a container with
other metal objects such as nails, coins, etc.
(3) Do not expose battery to water or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not incinerate the Battery even if it is severely
damaged or is completely worn out. The battery
can explode in a fire.
Be careful not to drop, shake or strike battery.
Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.