Reclining Child Seat For Bicycle - Frame Mounting System; Technical Characteristics; Technical Features; Table Of Contents Of Product - Polisport guppy rs+ Instrucciones De Uso

EN
RECLINING CHILD SEAT FOR BICYCLE
FRAME MOUNTING SYSTEM
For child safety and for your peace of mind, Polisport has developed the
perfect child carrying solution that's suitable for a wide range of adult
bicycles.
Our ergonomic child seats are all built with safety and comfort as the
primary goals.
In this manual you will find information on attaching the child bicycle seat
to the frame of your bicycle.
Carefully read the manual for a safe and correct installation of the child
bicycle seat.

TECHNICAL FEATURES

• This child bicycle seat must not be mounted to bicycles fitted with rear
shock absorbers.
• This child bicycle seat must not be mounted to a racing bicycle with
drop handlebar.
• This child bicycle seat must not be mounted to Motorized Vehicles such
as Mopeds and Scooters
• This child bicycle seat must not be mounted in bicycles with triangular,
square or carbon fiber frames
• This child bicycle seat must be assembled on bicycles with round and
oval frames with diameters ranging from Ø28 to Ø40 mm
• The child bicycle seat must be assembled on bicycles with wheels with
diameters of 26" and 28".
• This child bicycle seat is only suitable for carrying children with a
maximum weight of 22 Kg (and children with recommended ages
ranging from 9 months to 5 years of age - with the weight as the decisive
variable). Check the child's weight before using the child bicycle seat.
Under no circumstances should you use the child bicycle seat to transport
a child whose weight is above the permissible limit.
• Make sure that the weight and size of the child do not exceed the
maximum capacity of the seat, check it regularly and from time to time.
• If you have any doubts on fitting the child bicycle seat to your bicycle,
please contact your bicycle supplier for further information.

TABLE OF CONTENTS OF PRODUCT

A. Main seat
B. Safety belt
B1. Safety lock
B2. Belt adjuster
B3. Central belt adjuster
B4. Hole for belt adjustment
C. Safety belt for bicycle frame
D. Footrest strap
E. Footrest
F. Reclining plate
F1. Hand knob
F2. Plastic mounting plate
G. Hand knob
G1. Safety red ring

ASSEMBLY INSTRUCTIONS

1. Turn the child seat upside down as shown in the image. Remove the
metallic bracket (H) from the seat by cutting the straps.
2. To remove the mounting block, press the block button (I3) and remove
it according to the direction indicated in the picture.
3. Unscrew the hand knob (G1) and simultaneously lift the red security
ring (G2). Open the plastic mounting plate (F2).
4. Hold the metallic bracket (H) the same as in the picture and pass it
through the opening in the child bicycle seat.
4
| | www.polisport.com
H. Metallic bracket
I. Mounting block
I1. Screws M8x45
I2. Plastic mounting block
I3. Release button
I4. Metallic mounting plate
I5. Allen key no. 5
I6. Lock washer M8
I7. Safety device indicator
I8. Protective rubber
J. Gravity center
K. Batch serial number
L. Transport net
5. In order to adjust the child bicycle seat according to the bicycle size, set
the metallic bracket (H) into one of the three allowed positions to move
the seat backward or forward. At the beggining we suggest to place it on
the position No. 3.
6. Close the plastic mounting plate (F2); make sure it holds the metallic
bracket (H) and fasten the hand knob (G). As soon as the hand knob is
well tightened, make sure the security lever is properly held as shown in
the picture. This step is extremly important for the child and cyclist safety.
7. Remove the screws (I1) on the mounting block (I), with the Allen key
no. 5 (I5).
8. Before placing the block onto the frame, make sure that the protective
rubber (I8) is correctly positioned on front of the block.
9. Place the main body of the mounting block (I2) on the front of the
bicycle frame, and then place the metallic mounting plate (I4).
Note: If they are cables in this area make sure that they are correctly
positioned in the central groove of the metallic plate, (between the
protective rubber (I8) and the groove of the mounting plate (I4) and are
able to move freely).
10. Place the washer (I6) in the M8 screws (I1), and then screw them on
to the mounting block (I). Tighten the screws, with the Key (I5), so that the
mounting block (I) is secured but not fully tightened so that, if necessary,
you can adjust the height later. However, note that it should be tight to
make it easier to complete the next step. You need to tighten the 4
screws diagonally and in stages.
11. Place the edges of the metallic bracket (H) at the holes of the mounting
block (I) until you hear a click indicating the lock, and until the 2 green safety
device indicators pop up on the front of the mounting block. The child
bicycle seat will only be properly installed when the 2 green safety device
indicators are visible. This step is extremely important for the child's safety.
12. Centre and adjust the metallic bracket (H) at a height above the
rear wheel, so that later, when you add the weight of the child, the
child bicycle seat does not touch the wheel. Note that the metallic
bracket (H) should be positioned at a maximum of 10 cm away from
the wheel. The child seat has a center of gravity (J) (engraved on the
child seat) that must be positioned in front of the rear wheel axle. If it
is positioned behind the axle, the distance must not exceed 10 cm.
If the center of gravity is at a upper distance from the axle, adjust the
metal bracket to one of the available positions. Special care must also be
taken when positioning the child seat to ensure that the cyclist does not
touch the child seat with his feet when cycling.
Note: In Germany, according to the German Traffic Law StVZO, bicycle
seats may only be fixed so that 2/3 of the seat depth or the Gravity Center
of the seat is located between the front and rear axle of the bicycle.
13. After adjusting the height and positioning of the seat, hand tighten
the mounting block (I) to ensure that it cannot move. This tightening must
be manual and is extremely important for the safety of the child. Make
sure that the mounting block (I) is firmly attached. You need to hand tight
the 4 screws diagonally, with the same force and in stages (I5).
14. Pass the safety belt (C) around the bicycle frame. Adjust it as shown
in the picture, under tension. Make sure that remain loosen belt is not in
contact with the wheel. This step is extremely important for the child's
safety.
15. To place the child in the seat, first fully extend the belt straps (B),
sliding the adjusters (B2). This makes it easier to put the child in the seat.
To put the child in the seat, open the lock (B1) of the safety belt (B) and
press the three buttons of the lock (B1) as indicated.
According to the child growth you can adjust the height of the belt on the
hole for belt adjustment (B4).
Note: Before starting the journey, always check that the child is secured
and that the belt is snug but not so tight that it hurts the child. We
recommend that the child's helmet be put on after the belt is adjusted.
16. To adjust the height of the footrest (E) to fit your child, release the
footrest (E) from the seat (A) by pressing the two fasteners together and lift
the footrest as indicated in the picture (it may be necessary to apply some
pressure to the fasteners).
17. To reattach the foot rests, first engage the top pin, and push the
footrest (E) down to lock the clips into the slots holes.