Tabla de contenido
Idiomas disponibles
Idiomas disponibles
3) Connect the amplifier to the output jacks AMP (17).
4) Connect a recording unit to the output jacks REC
(16) if audio recordings are desired.
5) Connect the supplied plug-in transformer to the jack
(15) and then to a mains socket (230 V~/50 Hz).
6) Before switching on the mixer, the channel faders
(9) and the microphone volume control (7) should
be set to minimum to avoid loud switching noises.
Then, switch on the mixer with the switch (2). The
LED above the switch lights to indicate operation.
7) Switch on the connected units.
5 Operation
Before taking the mixer into operation for the first time,
set the tone controls (5 and 6) as well as the cross-
fader (12) to center position and the talkover switch
(13) to OFF.
5.1 Mixing of the connected audio sources
1) Adjust the volume of the input channels CH 1 and
CH 2 with the faders (9) and the volume of the DJ
microphone connected to the jack (10) with the DJ
MIC control (7). The stereo output level is displayed
by the 7-step LED level display (1). At 0 dB the
mixer is at its rated maximum output. Overloads are
indicated via the level display by lighting of the red
LEDs.
The faders of the channels CH 1 and CH 2 should
2
be at approx.
/
of the maximum after the level ad -
3
justment so that there is sufficient control range for
fading in and out. If the faders are almost at mini-
mum or maximum position, the levels have to be
matched by adjusting the input amplification: Turn
up resp. turn back the GAIN controls (4) corre-
spond ingly.
2) Adjust the desired sound characteristic for channels
CH 1 and CH 2 with the TREBLE controls (5) and
the BASS controls (6): The high and low frequen-
cies can be increased resp. decreased by 12 dB.
The frequency response is not affected if the con-
trols are in center position.
3) Fading between the channels CH 1 and CH 2 is
possible via the crossfader (12). If the crossfader is
in center position, both channels are fed to the out-
puts simultaneously.
5.2 Monitoring of the channels
Via the monitoring function it is possible to monitor the
input channels CH 1 and CH 2 individually by head-
phones. The level of the monitored signal is indepen-
dent of the setting of the corresponding channel fader.
By monitoring of an input channel the best moment for
fading in the corresponding audio source can be se -
lected.
1) Connect stereo headphones (impedance ≥ 8 Ω) to
the PHONES jack (14).
2) Select the channel CH 1 or CH 2 with the selector
switch PFL ASSIGN (11).
3) Adjust the desired headphones volume with the
PFL control (8).
Caution! Do not adjust the headphones to a high
volume. Permanent high volumes may
damage a person´s hearing! The human
ear gets accustomed to high volumes
which do not seem to be that high after
some time. Therefore, do not further
increase a high volume after getting
used to it.
5.3 Annoucements via the DJ microphone
For better intelligibility of a microphone announce-
ment, the levels of the channels CH 1 and CH 2 can be
decreased by 16 dB. Adjust the TALKOVER switch
(13) to position ON.
The talkover function is deactivated in the OFF
position.
6 Specifications
Inputs
1 × mic, mono: . . . . . . . . . . . 1.5 mV/ 600 Ω
2 × phono, stereo: . . . . . . . . 3 mV/50 kΩ
2 × line, stereo: . . . . . . . . . . 150 mV/50 kΩ
Outputs
1 × amp:. . . . . . . . . . . . . . . . 1 V/600 Ω
1 × record: . . . . . . . . . . . . . . 0.5 V/600 Ω
General
Frequency range:. . . . . . . . . 20-20 000 Hz
THD: . . . . . . . . . . . . . . . . . . 0.1 %
S/N ratio
Line: . . . . . . . . . . . . . . . . . 61 dB
Phono: . . . . . . . . . . . . . . . 56 dB
Mic: . . . . . . . . . . . . . . . . . 49 dB
Equalizer
2 × bass: . . . . . . . . . . . . . ±12 dB/50 Hz
2 × treble:. . . . . . . . . . . . . ±12 dB/10 kHz
Talkover: . . . . . . . . . . . . . . . -16 dB
Headphones output: . . . . . . ≥ 8 Ω, stereo
Power supply: . . . . . . . . . . . 12 V~/600 mA
Permissible
operating temperature: . . . . 0-40 °C
Dimensions (W × H × D):. . . 164 × 77 × 218 mm
Weight:. . . . . . . . . . . . . . . . . 1.2 kg
Connections
Mic: . . . . . . . . . . . . . . . . . . . 1 × 6.3 mm (
Headphones: . . . . . . . . . . . . 1 × 6.3 mm (
All other audio connections:. 12 × RCA
Power supply: . . . . . . . . . . . 3.5 mm jack
Subject to technical modification.
All rights reserved by MONACOR
Co. KG. No part of this instruction manual may be reproduced in
any form or by any means for any commercial use.
via supplied plug-in
transformer
(230 V~/50 Hz/10 VA)
1
/
") jack
4
1
/
") jack
4
®
INTERNATIONAL GmbH &
GB
7
Tabla de contenido
