EINHELL GE-PM 53/2 S HW-E Li Manual De Instrucciones Original página 31

engine start/stop lever (Fig. 5b) with one
hand. The other hand is on the Start button
(Fig. 1/Item 10).
4. Start the engine by pressing the Start button.
Release the Start button immediately once
the engine has started. Pressing the Start
button again while the engine is running will
damage the starting system. Important! In
cold weather, it may be necessary to repeat
the starting process several times.
6.1.2 Starting up with the reversing starter
1. Ensure that the ignition cable is connected to
the spark plug.
2. Press the fuel pump (primer) (Fig. 6/Item 2)
three times. You can skip this point if the engi-
ne has already warmed up.
3. Stand behind the lawn mower. Actuate the
engine start/stop lever (Fig. 5b) with one
hand. The other hand must be on the starter
handle.
4. Start the engine using the reversing starter
(Fig. 1/Item 9). To do this pull out the handle
approx. 10 –15 cm (until you feel a resistance)
and then start the engine with a sharp tug.
If the engine does not start, tug the handle
again.
Note! Never allow the actuator cable to snap
back.
Note! In cold weather, it may be necessary to
repeat the starting process several times.
Drive unit
Drive lever/clutch lever (Fig. 5a/Item 1b):
If you press this (Fig. 5c) the clutch for the drive
will be closed and the lawnmower will start to
move with the engine running. Release the drive
lever in good time to stop the moving lawnmower.
Practice starting and stopping before you use the
mower for the fi rst time until you are familiar with
controlling the mower.
6.2 Tips on mowing properly
Danger!
Never open the chute fl ap when the grass
bag has been detached (to be emptied) and
the engine is still running. The rotating blade
can cause serious injuries!
Always carefully fasten the chute fl ap and
debris bag. Switch off the engine before you
remove them.
Anl_GE-PM_53_2_S_HW-E_Li_SPK9.indb 31 Anl_GE-PM_53_2_S_HW-E_Li_SPK9.indb 31
GB
Whenever you need to perform any kind of
adjustment, maintenance or repair work,
switch off the engine and wait until the blade
no longer rotates. Pull off the spark plug
connector.
Mowing
The engine is confi gured for an optimal grass cut-
ting speed, for ejecting grass into the debris bag,
and for many years of use.
Only use a sharp blade that is in good condition.
This will prevent the grass blades from fraying
and the lawn from turning yellow.
Try to mow in straight lines for a nice, clean look.
The swaths should overlap each other by a few
centimeters in order to avoid stripes.
Keep the underside of the mower housing clean
and remove grass build-up. Deposits not only
make it more diffi cult to start the mower; they
decrease the quality of the cut and make it harder
for the equipment to bag the grass.
Always mow along inclines (not up and down).
You can prevent the lawn mower from slipping
down by holding a position at an angle upwards.
Select the cutting height according to the length
of the grass. If necessary, mow a number of times
so that you never cut more than 4cm of grass in
one go.
Switch off the engine before doing any checks on
the blade. Keep in mind that the blade continues
to rotate for a few seconds after the engine has
been switched off . Never attempt to manually
stop the blade. Regularly check to see if the
blade is securely attached, is in good condition
and is sharp. If the contrary is the case, sharpen
the blade or replace it. In the event that the blade
strikes an object, immediately switch off the lawn
mower and wait for the blade to come to a com-
plete stop. Then inspect the condition of the blade
and the blade mount. Replace any parts that are
damaged.
Mulching (Fig. 4b)
In mulching mode the cuttings are shredded in
the enclosed mower housing and then spread
back onto the lawn. It is not necessary to gather
and dispose of the grass.
Mulching is only possible if the lawn is relatively
short..
- 31 -
10.09.2019 11:46:06 10.09.2019 11:46:06