Tabla de contenido
Idiomas disponibles
Idiomas disponibles
12
English
1
SAFETY INSTRUCTIONS
1.1
The appliance you have purchased is a technologically advanced
product designed by one of the leading European manufacturers
of high pressure pumps. To obtain the best performance from
your unit, read this booklet carefully and follow the instructions
each time you use it. During connection, use and servicing of
the appliance, take all possible precautions to protect your own
safety and that of the people in the immediate vicinity. Read the
safety regulations carefully and comply with them on all occasions;
failure to do so may put health and safety at risk or cause expensive
damage.
2
SAFETY RULES/RESIDUAL RISKS
2.1
SAFETY "MUST NOTS"
2.1.1
inflammable or toxic liquids, or any products which are not
compatible with the correct operation of the appliance.
2.1.2
i
njury hazard
people or animals.
2.1.3
e
lectric shock hazard
towards the unit itself, electrical parts or towards
other electrical equipment.
2.1.4
s
hort circuit hazard
when it is raining.
2.1.5
i
. This appliance is noT intended for use
njury hazard
by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
2.1.6
e
lectric shock hazard
and/or socket with wet hands.
2.1.7
e
lectric shock and short circuit hazard
noT use the appliance if the electrical cable is
damaged.
2.1.8
e
xPlosion hazard
high pressure hose is damaged.
W
: High pressure hoses, fittings and couplings are important
arning
for the safety of the appliance. Use only hoses, fittings and
couplings recommended by the manufacturer.
2.1.9
a
ccident hazard
position.
2.1.10
a
ccident hazard
the appliance, if not, inform your dealer. Units without
plates must noT be used as they are unidentifiable and potentially
dangerous.
2.1.11
e
xPlosion hazard
the setting of the safety valve or the safety devices.
2.1.12
h
azardous alteration of oPerating Performance
alter the original diameter of the spray head nozzle.
2.1.13
a
ccident hazard
2.1.14
s
hort circuit hazard
pulling on the ELECTRICAL CAbLE.
2.1.15
Make sure that cars do not drive over the high pressure hose.
2.1.16
e
. Do noT move the appliance by pulling on the
xPlosion hazard
high pressure hose.
e
xPlosion or Poisoning hazard
Do noT use the appliance with
. Do noT direct the water jet towards
. Do noT direct the water jet
. Do noT use the appliance outdoors
. Do noT touch the plug
. Do noT use the appliance if the
. Do noT jam the trigger in the operating
. Check that the data plates are affixed to
. Do noT tamper with or adjust
. Do noT
. Do noT leave the appliance unattended.
. Do noT move the appliance by
2.1.17
e
xPlosion hazard
other pressurised components, the high pressure jet is potentially
dangerous. Do not use the rotating nozzle kit, and always keep the
jet at a distance of at least 30 cm during cleaning.
2.2
SAFETY "MUSTS"
2.2.1
s
hort circuit hazard
pRoTECTED against the water jet.
2.2.2
compliance with all applicable regulations (iEC 60364-1).
The appliance may cause network noise DURinG startup.
• Use of a safety residual current circuit-breaker (R.C.C.B.) will
provide additional protection for the operator (30 mA).
Models supplied without plug must be installed by qualified staff.
.
Use only authorized electrical extension leads with suitable
conductor gauge.
2.2.3
i
njury hazard
all the protective clothing and equipment needed to ensure the
operator's safety.
2.2.4
a
ccidental start
appliance, REMovE the plug.
2.2.5
i
njury hazard
firmly to counteract the recoil.
2.2.6
According to Din 1988, the appliance may only be connected to
the mains drinking water supply if a backflow preventer valve with
drain facility is installed in the supply hose.
2.2.7
a
ccident hazard
be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard. Maintenance
and/or repair of electrical components MUsT be carried out by
. Do
qualified staff.
2.2.8
i
njury hazard
disconnecting the unit hose.
2.2.9
a
ccident hazard
time that the screws are fully tightened and that there are
no broken or worn parts.
2.2.10
which will not corrode the coating materials of the high pressure
hose/electrical cable.
2.2.11
2.2.12
W
arning
cleaning agent supplied or recommended by the
manufacturer. The use of other cleaning agents or chemicals may
adversely affect the safety of the appliance.
. When directed towards tyres, tyre valves or
. All electrical conductors MUsT bE
e
. The appliance MUsT onLY
lectric shock hazard
bE ConnECTED to an adequate power supply in
. High pressure may cause parts to rebound: wear
-
. before doing work on the
uP hazard
. before pressing the trigger, GRip the gun
c
. CoMpLY WiTH the
ontamination
hazard
requirements of the local water supply company.
. if the supply cord is damaged, it must
. DisCHARGE residual pressure before
. before using the appliance, CHECK every
e
xPlosion and electric shock
. onLY UsE detergents
hazard
i
. EnsURE that all people or animals
njury hazard
keep a minimum distance of 16 yd. (15m) away.
: This appliance has been designed for use with the
Tabla de contenido
