Before Use - HewiTool GBNT 1665 Instrucciones De Manejo

English
3. Check on safety
CAUTION
Unauthorized persons (including children) must be
kept away from the equipment.
Wear eye protector.
Check the retaining screws which fix the top cover,
etc. for tightness.
Check the tool for defective or rusty parts.
Check whether or not the push lever works correctly
without nails, fuel cell and battery. Also check whether
or not any dirt has adhered to the moving parts of the
push lever.
Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)
Do not operate the push lever or trigger while
installing the battery.
Make sure the battery indicator light is flashing GREEN
(See Fig. 5).
If the battery indicator light is flashing RED, the battery
doesn't have enough power and it needs to be
charged.
BATTERY INDICATOR LIGHT
– Flashing GREEN: Enough power remaining (The
– Flashing RED: Insufficient power remaining (The
light turns steady during operation).
– OFF: The battery is extremely empty. Charge the
battery.
2. Insert fuel cell into the tool
(1) Push up and pull out the actuater (See Fig. 6).
(2) Insert the fuel cell into the tool (See Fig. 7).
(3) Insert the stem of fuel cell into the hole of adaptor
(See Fig. 8).
(4) Close the actuater (Fig. 9).
3. Load nails
CAUTIONS
When loading nails into Nailer,
(1) do not depress trigger;
(2) do not depress push lever; and
(3) keep your face, hands feet and other body parts,
as well as those of other persons away from the
nose muzzle to avoid possible injury during usage
and carrying.
<GBNT1665>
(1) Insert nail strip into rear of magazine (See Fig. 10).
(2) Slide the nail strip forward in the magazine (See Fig. 11).
(3) Push the nail feeder (A) to engage the nail feeder (B)
to the nail strip (See Fig. 12).
NOTE
Use nail strip of more than 10 nails.
The Nailer is now ready to operate.
Removing the nails:
1 Pull the nail feeder (B) backward (See Fig. 13).
2 Return the nail feeder (B) forward quietly while
pushing the nail feeder (A).
3 Pull out nails from the back of the magazine (See Fig.
14).
<GBNF1850>
(1) Lightly press the stop lever and gently pull out the
magazine cover. (See Fig. 15)
49
light turns steady during
operation).
(2) Set nail strip into the magazine and keep the points
of nails in contact with groove. (See Fig. 16)
(3) Slide the nail strip into the blade guide. (See Fig. 17)
(4) Confirm that nail strip is placed with side guide
grooves and groove properly, then push the magazine
cover forward to be latched.
NOTE
The nails shown in page 47 can be loaded onto the
side guide groove of the magazine without any
adjustment.
Always keep the points of nails in contact with Groove.
Magazine
Side guide
groove
Nail
Groove
Use nail strip of more than 5 nails.
The Nailer is now ready to operate.
Removing the nails:
1 Lightly press the stop lever and gently pull out the
magazine cover.
2 Remove the nails from the nailer.
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a
work bench on floor. Also, never face the nail outlet
toward any part of a person.
HOW TO USE THE NAILER
CAUTION
Never use the top cover or housing of this device as a
hammer.
Take precautions to ensure the safety of persons in
the vicinity during operation.
Squeeze the push lever when drive a nail, otherwise
the piston can not return correctly.
Make sure the nailing depth when the temperature is
above 40°C or below 0°C.
Using the tool for an extended period may lead to oil
around the exhaust outlet or nose, resulting in
spattering.
To ensure that the material to be nailed stays clean,
wipe off any oil that gets on the tool.
1. Nailing procedures
This power tool is equipped with a FULL SEQUENTIAL
ACTUATION MECHANISM.
Gap