Key-Tone On/Off; Call Tones - Topcom Twintalker 9500 Manual De Usuario

8
• If you press the
PTT
code, the PMR will go back in stand-by mode on the channel with
the CTCSS code.
• If no CTCSS code is detected there is a chance that DCS is
selected by the user. In this case you can scan for the DCS code.
(section 13.10.3)
13.10.3 Scanning for a DCS code
• Press the
00" flashes on the display for the selected radio channel.
• Press the
DCS scan.
Once there is a transmission on the channel, the DCS code (if used) will be detected and
displayed.
If you press the button
PTT
PMR will go back in stand-by mode on the channel with the DCS code.

13.11 Call Tones

A call tone alerts others that you want to start talking.
13.11.1 Setting the Call Tone
The Twintalker 9500 has 15 call tones.
• Press the
the current call tone is flashing.
• Press the
another Call Tone.
• Press the
mode.
13.11.2 Sending a call Tone
6
Press the button briefly. The call tone will be transmitted on the set channel.
13.11.3 Call tone reception type
7
• Press the -button nine times.
• Press the -button 11 or
1. Tone only
2. Tone + vibration
3. Vibration only
Press the -button 12 to confirm and return to stand-by mode.
PTT
button 12 while listening to a found CTCSS
7
-button seven times : "SCAN" and "DCS
11 10
-button or the -button to start the
12 while listening to a found DCS code, the
7
- button eight times, "C" is displayed and
- button 11 or the - button 10 to change to
- button 12 to confirm and return to stand-by
PTT
10
-button to select the call tone reception type.
13.12 Roger Beep On/Off
After the -button 12 is released, the unit will send out a roger beep to confirm that you have
PTT
stopped talking.
To set the Roger Beep.
• Press the - button
• Press button 11
Beep (OFF).
• Press the - button
PTT
standby mode.

13.13 Key-Tone On/Off

When a button is pressed, the unit will beep briefly.
To set the key-tone.
• Press button
• Press button 11
Tones (OFF).
• Press the - button
PTT
standby mode.
13.14 Dual Channel Monitor function
In stand-by, the PMR is set on one channel with CTCSS/DCS code. The PMR will only receive
signals transmitted on that channel with the CTCSS/DCS code.
Dual Channel Monitor (DCM) allows you to monitor a second channel with CTCSS/DCS code.
• Press the
flash on the display.
• Press the
channel.
• Press the
and go to CTCSS selection. (Press the
again to go to DCS selection)
• Press the
the CTCSS code or DCS code.
• Press the
mode.
• To disable the function select "OFF" when selecting the
DCM channel.
When the Dual Channel Monitor function is activated, the PMR will switch sequentially between
the standby channel + CTCSS/DCS code and the Dual Channel + CTCSS/DCS code.
7
ten times. 'rO' will be displayed.
to enable (ON) or button 10 to disable the Roger-
12 to confirm your selection and return to the
7
eleven times. 'tO' will be displayed.
to enable (ON) or button 10 to disable the Key
12 to confirm your selection and return to the.
7
-button twelve times," DCM OFF" will
-button 11 or the -button 10 to change the
7
-button to confirm the channel selection
-button
-button 11 or the -button 10 to change
-button 12 to confirm and return to stand-by
PTT
Twintalker 9500
7