Console (Fig. E-1); Buttons - Tunturi T85 Manual Del Usuario

English
‼ NOTE
• Console will show "please return safety key" code when safety
key is not in (correct) position during start up.
Circuit breaker (Fig. E-2B)
The equipment is equipped with a circuit breaker that interrupts the
circuit when the electricity load is above the maximum capacity. When
this occurs, the circuit breaker must be pressed.
⚠ WARNING
• Before pressing the circuit breaker, remove the mains plug from
the equipment.
If the equipment shuts down, proceed as follows to restart the
equipment:
- Remove the mains plug from the equipment.
- Press the circuit breaker to restart the equipment.
- Insert the mains plug into the equipment.
‼ NOTE
• Some circuit breakers used in homes are not rated for high
inrush currents that can occur when a treadmill is first turned
on or even during normal use. If your treadmill is tripping the
circuit breaker (even though it is the proper current rating and
the treadmill is the only appliance on the circuit) but the circuit
breaker on the treadmill itself does not trip, you will need
to replace the breaker with a high inrush type. This is not a
warranty defect. This is a condition we as a manufacture have no
ability to control.
Unfolding and folding the
equipment (fig. F1-F2)
The equipment can be unfolded for use (fig. F1) and folded for
transport and storage (fig. F2).
Refer to the illustrations for the correct way of unfolding and folding
the equipment.
⚠ CAUTION
• Before folding the equipment, make sure that the incline is 0. If
the incline is not 0, folding will damage the mechanism.
Adjusting the support feet
The equipment is equipped with 4 support feet. If the equipment is
not stable, the support feet can be adjusted.
- Turn the support feet as required to put the equipment in a stable
position.
- Tighten the locknuts to lock the support feet.
‼ NOTE
• The machine is the most stable when all support feet are turned
fully in. Therefore start to level the machine by turning all
support feet fully in, before turning out the required support
feet to stable the machine.

Console (fig. E-1)

⚠ CAUTION
• Keep the console away from direct sunlight.
• Dry the surface of the console when it is covered with drops of
sweat.
• Do not lean on the console.
• Only touch the display with the tip of your finger. Make sure that
your nails or sharp objects do not touch the display.
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 4 minutes.

Buttons

Enter/ Start
- Sport mode confirmation
- Option confirmation under User/Setting mode
- Confirmation of working item on setting screen
- Setting value confirmation.
- Main screen switching between bpm / incline Profile
- Main screen switching between Video / Profile during T-Road
Back/ Stop
- Move back to previous window
- Stop the active training
User/ + (scale up)
- Open User's setting.
- Scale up intensity in workout mode.
Press once to increase 1%
Press and hold to increase the intensity faster.
‼ NOTE
• It is not possible to deform the profile, so the highest pre
programmed intensity is the scaling limit.
Select/ - (scale down)
- Switch LED display monitor.
- Scale down intensity in workout mode.
Press once to decrease 1%
Press and hold to decrease the intensity faster.
‼ NOTE
- It is not possible to deform the profile, so the lowest pre
programmed intensity is the scaling limit.
Speed +
- Increases the speed (0.5 ~ 16.0 km/h).
- Pressing once increases the speed 0.1 km/h.
- Pressing and holding for two seconds will increase the speed faster.
- Scroll programs and change values in programming mode.
Speed -
- Decreases the speed (0.5 ~ 16.0 km/h).
- Pressing once decreases the speed 0.1 km/h.
- Pressing and holding for two seconds will decrease the speed
faster.
- Scroll programs and change values in programming mode.
Speed control hot keys:
Speed Hot Keys are set as : 6, 9, 12. ( Metric 3.7/ 5.6/ 7.5 )
For example, the speed changes from any speed to 9 km/h by
pressing the Speed Hot Key 9.
Handle bar speed quick-access keys:
- + Same as Speed +.
- – Same as Speed –.
Incline control +
- Increases the incline (0 ~ 15 +1).
- Scroll programs and change values in programming mode.
Incline control -
- Decreases the incline (0 ~ 15 -1)
- Scroll programs and change values in programming mode.
Incline control hot keys�
Incline Hot Keys are set as 0, 5, 10.
For example, the incline level changes from any level to 5 by pressing
the Incline Hot Key 5.
Handle bar incline quick-access keys:
- + : Same as Incline +.
- - : Same as Incline –.
2 0