Adjusting The Support Feet (Fig. F7-F8); Console (Fig. E); Buttons; Explanation Of Display Items - Tunturi Cardio Fit T40 Manual Del Usuario

‼ NOTE
• Console will show E7 code when safety key is not in (correct)
position during start up�
Circuit breaker (Fig. E-2 B)
The equipment is equipped with a circuit breaker that interrupts the
circuit when the electricity load is above the maximum capacity� When
this occurs, the circuit breaker must be pressed�
⚠ WARNING
• Before pressing the circuit breaker, remove the mains plug from
the equipment�
If the equipment shuts down, proceed as follows to restart the
equipment:
- Remove the mains plug from the equipment�
- Press the circuit breaker to restart the equipment�
- Insert the mains plug into the equipment�
‼ NOTE
• Some circuit breakers used in homes are not rated for high inrush
currents that can occur when a treadmill is first turned on or even
during normal use� If your treadmill is tripping the circuit breaker
(even though it is the proper current rating and the treadmill is
the only appliance on the circuit) but the circuit breaker on the
treadmill itself does not trip, you will need to replace the breaker
with a high inrush type� This is not a warranty defect� This is a
condition we as a manufacture have no ability to control�
Unfolding and folding the
equipment (fig. F1-F2)
The equipment can be unfolded for use (fig� F1) and folded for
transport and storage (fig� F2)�
Refer to the illustrations for the correct way of unfolding and folding
the equipment�

Adjusting the support feet (Fig. F7-F8)

The equipment is equipped with adjustable support feet�
If the equipment feels unstable, wobbly, or not levelled well, these
support feet can be adjusted to make the required corrections�
- Turn the support feet in/ out as required to put the equipment in a
stable and as well possible levelled position�
- Tighten the locknut's* to lock the support feet�
�� QUICK TIP
• It is easier to do this with two persons, so one person can tilt the
equipment, while the other makes the needed adjustment�
Click to see our supportive YouTube video
https://youtu�be/E_7agKqaUIc
‼ NOTE
• The equipment is most stable when it is as low to the floor as
possible� Therefore, start to level the equipment by turning all
support feet fully in, before turning out the required support feet
to stabilize and level the equipment�

Console (fig. E)

⚠ CAUTION
• Keep the console away from direct sunlight�
• Dry the surface of the console when it is covered with drops of
sweat�
• Do not lean on the console�
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 10 minutes�

Buttons

Stop
- Stop workout�
Speed +
- Increases the speed (1�0 ~ 16 km/h)�
- Pressing once increases the speed 0�1 km/h�
- Pressing and holding for two seconds will increase the speed faster�
- Scroll programs and change values in programming mode�
Speed -
- Decreases the speed (1�0 ~ 16 Km/h)�
- Pressing once decreases the speed 0�1 km/h�
- Pressing and holding for two seconds will decrease the speed
faster�
- Scroll programs and change values in programming mode�
Incline +
- Increases the incline (0~10 ±1)�
Incline -:
- Decreases the incline (0~10 ±1)
Mode
- Select program mode
- Confirm setting to enter next step in programming mode�
Prog
- Select program mode� ( P1~P36, U1~U3, FAT)
Start/ Pause
- Start selected workout, or restart pause workout when being in
pause mode�
- Pause active workout�
Speed hot keys:
Speed Hot Keys are set as: 3, 6, 9�
For example, the speed changes from any speed to 6 km/h by
pressing the Speed Hot Key 6�
Incline hot keys�
Incline Hot Keys are set as 2, 4 & 8�
For example, the incline level changes from any level to 4 by pressing
the Incline Hot Key 4�

Explanation of display items

Speed
- Shows the actual treadmill speed in workout mode�
Incline
- Shows the actual treadmill incline in workout mode�
- Shows target incline in programming mode�
1 9
GB