Console (Fig. E-1); Buttons; Explanation Of Display Items (Fig. H) - Tunturi T80 Manual Del Usuario

English
If the equipment shuts down, proceed as follows to restart the
equipment:
- Remove the mains plug from the equipment.
- Press the circuit breaker to restart the equipment.
- Insert the mains plug into the equipment.
‼ NOTE
•
Some circuit breakers used in homes are not rated for high
inrush currents that can occur when a treadmill is first turned
on or even during normal use. If your treadmill is tripping the
circuit breaker (even though it is the proper current rating and
the treadmill is the only appliance on the circuit) but the circuit
breaker on the treadmill itself does not trip, you will need
to replace the breaker with a high inrush type. This is not a
warranty defect. This is a condition we as a manufacture have no
ability to control.
Unfolding and folding the
equipment (fig. F1-F2)
The equipment can be unfolded for use (fig. F1) and folded for
transport and storage (fig. F2).
Refer to the illustrations for the correct way of unfolding and folding
the equipment.
⚠ CAUTION
• Before folding the equipment, make sure that the incline is 0. If
the incline is not 0, folding will damage the mechanism.
Adjusting the support feet
The equipment is equipped with 4 support feet. If the equipment is
not stable, the support feet can be adjusted.
- Turn the support feet as required to put the equipment in a stable
position.
- Tighten the locknuts to lock the support feet.
‼ NOTE
• The machine is the most stable when all support feet are turned
fully in. Therefore start to level the machine by turning all
support feet fully in, before turning out the required support
feet to stable the machine.

Console (fig. E-1)

⚠ CAUTION
• Keep the console away from direct sunlight.
• Dry the surface of the console when it is covered with drops of
sweat.
• Do not lean on the console.
• Only touch the display with the tip of your finger. Make sure that
your nails or sharp objects do not touch the display.
‼ NOTE
• The console switches to standby mode when the equipment is
not used for 4 minutes.

Buttons

Stop/ Reset
- Press once, stop workout/ treadmill gently.
- Press twice, stop workout/ treadmill more rapidly.
- Reset console when press and hold for 2 seconds in "stop mode"
Start/ Pause
- Start selected workout, or restart pause workout when being in
pause mode.
- Pause active workout.
Prog
- Press to Cycle through the possible programmes.
(P0/ P1~P36/ U01~U03/ HRC1~HRC3/ FAT)
Mode
- Cycle between target setting parameters in programming mode.
- Reset time target when setting time goal for "P1~P36" programs.
Speed +
- Increases the speed (0.8 ~ 22.0 km/h).
- Pressing once increases the speed 0.1 km/h.
- Pressing and holding for two seconds will increase the speed faster.
- Scroll programs and change values in programming mode.
Speed -
- Decreases the speed (0.8 ~ 22.0 km/h).
- Pressing once decreases the speed 0.1 km/h.
- Pressing and holding for two seconds will decrease the speed
faster.
- Scroll programs and change values in programming mode.
Speed hot keys:
Speed Hot Keys are set as 6, 9, 12.
For example, the speed changes from any speed to 9 km/h by
pressing the Speed Hot Key 9.
Handle bar speed quick-access keys:
- + Same as Speed +.
- – Same as Speed –.
Incline +
- Increases the incline (0 ~ 15 +1).
- Scroll programs and change values in programming mode.
Incline -
- Decreases the incline (0 ~ 15 -1)
- Scroll programs and change values in programming mode.
Incline hot keys�
Incline Hot Keys are set as 0, 5, 10.
For example, the incline level changes from any level to 5 by pressing
the Incline Hot Key 5.
Handle bar incline quick-access keys:
- + : Same as Incline +.
- - : Same as Incline –.

Explanation of display items (Fig. H)

Speed
- Shows the actual treadmill speed in workout mode.
- Shows target speed in programming mode.
- Shows program selection when being in program mode.
Incline
- Shows the actual treadmill incline in workout mode.
- Shows target incline in programming mode.
Distance
- Shows the ran distance workout mode.
- Shows left distance when workout in countdown mode.
- Shows the target distance when being in programming mode.
Time
- Shows the ran time in workout mode.
- Shows left time when workout in countdown mode.
- Shows the target time when being in programming mode.
Steps
Console is able to count the amount of steps during your workout,
when keeping your speed higher than 3.0 km/h and user weight is at
least 40 kg.
Heart
- Shows the pulse rate in workout mode, or "P" when no pulse is
measured.
2 0