Tabla de contenido
Idiomas disponibles
Idiomas disponibles
FUNCTION ON THE CONTROL AND RESPONSE OF THE ALARM
1
Press
Functi on
Enable the alarm
Disable the alarm
Enable the alarm
Then
without sound
Disable the alarm
Then
without sound
Panic functi on
Then
For
Enable alarm wi-
3 Secs.
thout accelerometer
Localizati on
Press
Twice (2x)
Functi on
Available only in the TRIPLO i
For
Turn on the panel
3 Secs.
For 3 Secs,
Start Functi on
Then
1.1. ENABLE OR DISABLE PERIODIC TRANSMISSION (ONLY CX-1P)
The CX-1P control comes
from the factory with the
presence
transmission
THEN PRESS
DISABLED. Before use,
...unti l the led turns off and
fl ash 1 ti me (ENABLE).
make sure the presence
transmission is ENABLED.
...unti l the led turns off and
fl ash 2 ti mes (DISABLE).
If it is disabled, the lock
cycle will begin.
Aft er use, it is recommended that the periodic transmission be disabled to extend
CR2032 batt ery life (It is recommended that the batt ery be replaced every 4 months).
When the igniti on is turned on, the alarm will give 1 beep if the control batt ery is low.
8
Alarm Response
Blinkers fl ash once, siren beeps
once.
Blinkers fl ash twice, siren beeps
twice.
Blinkers fl ash once. (1x)
Blinkers fl ash twice. (2x)
Sets off the alarm for 30 secs
2 Beeps and blinkers fl ash 1
Blinkers fl ash for 15 secs
Turns on motorcycle's
15th line (Accessory positi on).
Starts the motorcycle
HOLD
...
CX-1P
CX-1P
PROGRAMMING CONTROLS
2
TURN ON
PRESS THE MASTER BUTTON
IGNITION
EMITS 3 BEEPS FOR EACH
TURN OFF
IGNITION
PROGRAMMED CONTROL
If the control is already programmed the siren will emit 1 beep. Each ti me a new
control is programmed to the control panel the memory is cleared. Therefore all
existi ng controls must be reprogrammed with the new one or they will not work.
ALARM FUNCTIONS
3
3.1. TRIGGERED ALARM
When the alarm is triggered, it immediately locks down. The alarm sounds for one
minute, then waits 10 seconds and reads the sensors again. Aft er the alarm has been
triggered ten consecuti ve ti mes by the accelerometer, this sensor is ignored unti l the
next acti vati on, unless the motorcycle is turned on.
3.2. USING THE CONTROL TO TURN ON THE MOTORCYCLE (ONLY MOTO TRIPLO i)
PRESS
SIREN EMITS
FOR 3 SECS.
1 BEEP
MOTORCYCLE TURNS ON
• Press
bu� on for 3 seconds. A beep will sound, the motorcycle's panel will be
acti vated, and if the
bu� on is pressed within 10 seconds the igniti on will turn on
(gray wire, positi ve current). As long as the
• To turn on the igniti on, the motorcycle must be in Neutral
• If you need to start the igniti on again, press the
• To turn off the motorcycle press the
will turn off .
• If the motorcycle is in gear, it will not be switched off to prevent it from accidentally
turning off when in moti on.
Before checking the control panel, give it 10 seconds aft er it has been acti vated to
stabilize all the sensors.
4
ENABLE OR DISABLE ALARM
The control panel can be switched on and off by programming (see table secti on 12,
functi on 2).
UNTIL THE SIREN
BEEPS
PRESS
AND
TOGETHER
PANEL TURNS ON
AUTOMATICALLY
PRESS
bu� on is held the output remains acti ve.
.
N
bu� on and then in 3 seconds
bu� on, 2 beeps will sound and the motorcycle
.
9
Tabla de contenido
