Rear Panel; Single Receiver - Fender FWG 2020 Manual De Instrucciones

Short push on l : Calls up a parameter for adjustment or con-
firms a selected value.
Long push on l : selects LOCK mode.
Short push on t : selects a menu item or decreases a parame-
ter value.
Short push on u : selects a menu item or increases a parameter
value.
4,5 RF LEDs: The green OK LED (4) is lit to indicate the receiver is
receiving RF signal, the red MUTE LED (5) indicates that no signal is
being received.
6 A and B diversity LEDs: These two LEDs are lit to indicate which
of the two antennas is currently active.
7 AF LEDs: Indicate the received audio level:
OK (green): -40 dB to +3 dB
CLIP (red): >3 dB (overload)
8 Infrared emitter: Transmits frequency data from the receiver to
the bodypack transmitter. The infrared emitter has a very narrow
radiation angle (approx. 10°) and a maximum range of 8 inches (20
cm) to make sure only one transmitter will be tuned to the same
frequency.
9 Output level control: This retractable rotary control attenuates
the level of the balanced audio output continuously by 0 to 30 dB.

Rear Panel

i Refer to fig. 2 on page iii.
10 DC IN: Locking DC input for connecting the included power
supply.
11 ANTENNA A/B: BNC sockets for connecting the two supplied UHF
antennas or optional remote antennas.
12 BALANCED: Balanced 3-pin XLR audio output for connecting to a
balanced input on a mixing console or amplifier.
13 UNBALANCED: Unbalanced 1/4" TS audio output jack for con-
necting to an instrument amplifier.
14 Output level switch: Slide switch for matching the BALANCED
output level to the input gain of the equipment connected
to the receiver. The switch has two positions, 0 and -30 dB. The
UNBALANCED output level is not adjustable.
15 Type plate indicating available carrier frequency ranges and
approval information.
Bodypack Transmitter
i Refer to fig. 4 on page iv.
17 Infrared sensor: Receives the infrared signal emitted by
the receiver for automatically setting the transmitter's carrier
frequency.
18 LCD display: Indicates the selected frequency in MHz or as a Preset
sub-channel, current mode, error messages, as well as the available
battery capacity in 1-hour increments for dry and 2-hour incre-
ments for rechargeable batteries.
19 ON-MUTE/PRG-OFF: This slide switch provides three positions:
ON: The output signal is fed to the transmitter for transmission to
the receiver (normal mode). The status LED (20) is lit green.
MUTE/PRG: The audio signal is muted. Sliding the switch to
"MUTE/PRG" places the transmitter in programming mode. To
switch the audio signal back on, slide the switch to "ON".
OFF: Power to the transmitter is off. The status LED (20) is dark.
20 Status LED: This bi-color LED indicates the following conditions:
Green: The battery will last for more than one hour, the transmit-
ter is in normal mode.
Red: The battery will be dead in less than one hour and/or the
audio signal is muted. Flashing red: Error message in the display.
Flashing red: Error message in the display.
Off: Power to the transmitter is off or the transmitter is in program-
ming mode.
22 Charging contacts: The recessed charging contacts allow you to
charge a rechargeable battery on the optional charger without
having to remove the battery from the transmitter.
25 Antenna: Permanently connected, flexible antenna.
26 Audio input: 3-pin mini XLR connector with line level pins that
automatically match the connector pin-out of the supplied ITC3
instrument cable. The ITC3 instrument cable lets you connect an
electric guitar, electric bass, or remote keyboard to the bodypack
transmitter.
27 Frequency sticker: Sticker attached to the transmitter, indicating
the available carrier frequency range and approval data.
28 Battery compartment for the supplied AA size 1.5 V dry battery
or a commercial 1.2 V, ≥2100 mAh NiMH AA size rechargeable
battery. The viewing window lets you check if there is a dry or
rechargeable battery inside the battery compartment. You can
also insert a white lettering strip (supplied) or a color code strip
(optional) into the viewing window.
29 Belt clip for fixing the transmitter to your belt.
30 MUTE jack: This jack allows you to connect the supplied terminal
connector for locking the ON-MUTE/PRG-OFF switch to prevent
operating errors.
31 Gain control: This rotary control inside the battery compartment
allows you to match the bodypack transmitter input gain to the
instrument you connected to the transmitter.
2. SETTING UP
Rack Mounting Receiver
• If you install one or more receivers into a 19" rack, either mount
the supplied antennas on the receiver front panel(s) or use remote
antennas. This is the only way to ensure optimum reception quality.

Single Receiver

i Refer to fig. 6 on page vi.
1. Unscrew the four rubber feet (1) from the receiver bottom panel.
2. Unscrew the two fixing screws (2) from each side panel.
3. Use the fixing screws (2) to screw the short bracket 3 to one side
panel and the long bracket (4) to the other side panel. The brackets
are contained in the supplied rack mounting kit.
4. Install the receiver in your rack.
3