Fender VAPORIZER Manual De Instrucciones página 8

Fender's Vaporizer amp evokes the 1950s-'60s age of the Space Race, when
the atom-age world became enthralled with spaceflight and spacecraft. When
the wild flights of fancy it launched permeated culture everywhere from film
and television to cars, guitars, appliances and more—everything was bright,
colorful and flashy. Garage bands blasted off with guitar music, and legions
of musicians who couldn't swing pro gear bashed away on department-store
guitars and amps.
The Vaporizer amp blasts you like a ray gun back to that exciting era.
Affordable and out of this world, it would've been right at home aboard a
Mercury capsule and down in the backyard fallout shelter. It would've been
stumbled on decades later in some pawnshop corner by an unconventional
guitarist with an ear for the distinctive and an eye for the stylish. It's the
Fender Vaporizer. Stand back...
PRODUCT REGISTRATION — Please visit:
NORMAL BRIGHT
A. NORMAL INPUT — Plug your guitar in here.
B. BRIGHT INPUT — Plug your guitar in here for a treble boost. You can
also plug a second guitar in here and use both inputs simultaneously.
C. VAPORIZER MODE INDICATOR — This red jewel illuminates when
"Vaporizer mode" has been selected from the footswitch. In Vaporizer
mode, the volume and tone controls are disabled and the amplifier is set
for maximum overdrive! See FOOTSWITCH {M}.
D. VOLUME — Controls the volume level of the "dry" guitar signal, without
any reverb effect. Use in combination with the REVERB {F} knob to adjust
the overall loudness and reverb blend for the amplifier.
E. TONE — Adjusts the tonal characteristics of the amplifier.
F. REVERB — Controls the volume level of the pure reverb signal, indepen-
dent of the VOLUME {D} knob.

TRY THIS . . . Turn the VOLUME knob all the way down, then turn up
the REVERB knob to create a full-strength, spacious effect!
G. POWER INDICATOR — This blue jewel illuminates when power is
switched on to the unit.
H. POWER SWITCH — Select the "ON" position to switch the unit on. Select
the "OFF" position to switch the unit off.
TYPE: PR 2521
POWER REQUIREMENTS: 75W
POWER OUTPUT: 12W RMS into 8Ω @ 20%THD
INPUT IMPEDANCE: >68kΩ
SPEAKERS: Two 10", 16Ω Special Design Vaporizer (P/N 2521CSV014)
www.fender.com/product-registration
VOLUME
Specifications
Product specifications are subject to change without notice.
Features include:
• Two 12AX7 preamp tubes, two 6BQ5/EL84 output tubes
• 12 watts (output power)
• Two 10" 16-ohm Special Design Vaporizer speakers
• Internal speaker disconnects to let the amp's ¼" output be used for external
8-ohm speaker enclosures
• Two inputs (normal and bright)
• Volume, tone and reverb controls
• Spring reverb circuit independent of amp volume control; creates full, wet
reverb for moody "late-night" vibe and approximates the sound of playing
in a tunnel
• Single-button "wedge" footswitch for selecting "vaporizer mode"
(bypasses volume and tone controls for full-strength overload; indicated by
red jewel light)
• Available in Rocket Red, Slate Blue or Surf Green dimpled vinyl covering
TONE R EVERB
Rear Chassis (bottom view)
I. IEC POWER SOCKET — Connect the included power cord to a grounded
electrical outlet in accordance with the voltage and frequency ratings as
specified under "INPUT POWER" on the rear panel of your amplifier.
J. FUSE — Protects the unit in case of electrical faults. Replace a blown fuse
only with the type and rating specified under "FUSE" on the rear panel of
your amplifier.
K. REVERB CONNECTIONS — These jacks connect the amplifier to the
spring reverb unit.
L. SPEAKER OUTPUT — This jack must always be connected to a minimum
8-ohm, 15-watt speaker load when the power is switched on to prevent
damage to the unit.
M. FOOTSWITCH — Connect the included footswitch
here to enable selection of "Vaporizer mode."
TUBES: Two 12AX7 preamp; two 6BQ5/EL84 output
FOOTSWITCH: 1-button, Vaporizer mode (P/N 2521CSV018) included
HEIGHT: 17.0 in (43.18 cm) WIDTH: 24.75 in (62.87 cm)
WEIGHT: 37 lb (16.78 kg)
POWER ON
OFF
DEPTH: 10.5 in (26.67 cm)