Quick ASTER Serie Manual Del Usuario página 17

POS. DESCRIPTION
9 Screw
10 Mooring rope puller
11 Spring for pressure lever
12 Mooring rope puller pin
13 Pressure lever
14 Screw
15 Rope/chain stripper "AS"
16 Chain guide cover
17 Base
18 Plug
19 Gasket / jig Aster
20 Sensor
21 Circlip
22 Bearing
23 Flange
24 Shaft 700/1000W
25 Long shaft 700/1000W
26 Key
27 Key
28 Stud
29 Gearbox flange gasket
Top TG50
30 Gearbox 700/1000W
Quick TG50 series
31 Washer
32 Spring washer
33 Nut
34 Washer
35 Self-locking nuts
36 Gasket gearbox
37 Key
38A Electric motor 700W 12V
38B Electric motor 1000W 12V
38C Electric motor 700W 24V
38D Electric motor 1000W 24V
39A Motor casing watertight 700W
39B Motor casing watertight 1000W
40 Grommet 700/1000W
41 Terminal board cover 700/1000W PCCPPMMR0000
42 Screw
43 Bottom gasket 700/1000W
44 Bottom protec 700/1000W
45 Cable outlet
ASTER 700/1000W - REV004A
CODE
MBV0410MXTSC
MMSTTC08ASC0
MMTND08ASC00
Quick
MMTC08ASC000
ant to marine environments. In any case, any salt deposits
PDLVTD08ASCN
on the outside must be removed periodically to avoid cor-
MBV0512MXCE0
rosion and damage to the equipment. The parts where salt
MSN10ASX0000
may have built up should be washed thoroughly with fresh
SGMSGG08ASC1
water.
SGMSC08ASC00
MSR08XASC000
Once a year, the drum and the gypsy are to be taken apart
PGBSG10AS000
as follows:
KNREEDCL0000
MBAE3015Y000
DRUM VERSION
MBJ160060000
Use the handle (1) to loosen the bush (2); pull off the drum
MSVFLPRAS000
(3) and the top clutch cone (5); loosen the fixing screws (14)
MSAS10260R30
of the rope/chain stripper (15) and remove it. Pull off the
MSAS10300R30
gypsy (6).
MBH0807080X0
MBH0606020X0
NO-DRUM VERSION
MBP080807X00
Use the handle (1) to remove the gypsy cover (4); remove
the top clutch cone (5); loosen the fixing screws (14) of
PGFLRDTG5000
the rope/chain stripper (15) and remove it and pull off the
gypsy (6).
SLMR10TG5000
MBR08X000000
Clean all the parts removed to avoid corrosion, and grease
MBR08XDE0000
the shaft thread (24 and 25) and the gypsy (6) where the
MBD08MXEN000
clutch cones rest (5 and 7).
MBR061815X00
MBD06MXET000
Remove any oxide deposits from the terminals of the elec-
PGNP10000000
tric motor and the solenoid unit; grease them.
MBH050515F00
EMF071200000
EMF101200000
EMF072400000
EMF102400000
PCCCPM070000
PCCCPM100000
PCGPMMR00000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17