MIDI Implementado
Control Change
Bank Select
This message is received when the "MIDI Program change switch" of the MIDI mode is
set at ON.
Status
2nd byte
3rd byte
BnH
00H
mmH
BnH
20H
llH
n=MIDI channel :
0H-FH (ch.1-ch.16)
mm=Bank number (MSB) : 00H-7FH (0-127)
ll=Bank number (LSB) :
00H-7FH (0-127)
* Channel number can be received on the channel set in the Drum part.
* The Drum kit set corresponding to each Bank Select are as follows.
* Will not be affected by the received Bank number (LSB).
Bank Select
Progaram No
MSB
LSB
81
00
0 - 127
85
00
0 - 63
Modulation
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
01H
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Modulation depth :
00H-7FH (0-127)
Expression
This message is received when the "MIDI Expression switch" of the MIDI mode is set at
ON.
Status
2nd byte
3rd byte
BnH
0BH
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Expression :
00H-7FH (0-127)
Portamento
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
41H
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Control value:
00H-7FH (0-127)
0-63=OFF 64-127=ON
* Upon receipt of a Note On while the Portamento is on, continuous pitch change starts
with the previously sounded Note number or previously specified Source note number.
* The speed of the pitch change causad by Portamento is determined by the Portamento
Time parameter.
Portamento Control
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
54H
kkH
n=MIDI channel :
0H-FH (ch.1-ch.16)
kk=Source note number : 00H-7FH (0-127)
* A Note On message received immediately after a Portamento control will be sounded
with the pitch changing smoothly from the source note number.
* The speed of the pitch change caused by Portamento is determined by the Portamento
Time parameter.
Portamento Time
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
82
Drum Kit
Preset 0-127
User 0-63
Status
2nd byte
3rd byte
BnH
05H
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Portamento time :
00H-7FH (0-127)
* Adjusts the speed of the pitch change when Portamento is on or when Portamento con-
trol is used. "0" represents the highest rate.
Effect1 (Reverb Level / Delay Feedback)
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
5BH
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Control value :
00H-7FH (0-127)
* Channel number can be received on the channel set in the Drum part.
* This message determines the level of Reverb when the selected Effect is Reverb, or the
Feedback when the selected effect is Delay.
* Reverb/Delay effect is not obtained if the Reverb/Delay send level of each instrument
in the Drum kit is not set at high.
Effect3 (Flanger Level)
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
5DH
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Control value :
00H-7FH (0-127)
* Channel number can be received on the channel set in the Drum part.
* Flanger effect is not obtained if the Flanger send level of each instrument in the Drum
kit is not set at high.
Data Entry
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
06H
mmH
BnH
26H
llH
n=MIDI channel :
0H-FH (ch.1-ch.16)
mm=MSB value of the parameter specified by RPN/NRPN
ll=LSB value of the parameter specified by RPN/NRPN
Volume
This message is received when the "MIDI Volume switch" of the MIDI mode is set at ON.
Status
2nd byte
3rd byte
BnH
07H
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Volume :
00H-7FH (0-127)
* The volume of the Track corresponding to the MIDI channel through which the messa-
ge is received can be adjusted.
Real volume is determined by (Volume value) x (Expression value).
Panpot
This message is received when the "MIDI Control change switch" of the MIDI mode is set
at ON.
Status
2nd byte
3rd byte
BnH
0AH
vvH
n=MIDI channel :
0H-FH (ch.1-ch.16)
vv=Panpot :
00H-40H-7FH (0, 1-64-127)
* 0, 1 means Left, 64 means Center 127 means Right. 127 steps in total can be set.
Panpot of the instrument corresponds to the received MIDI channel is changed relati-
vely as the received value.
Capítulos
