Important; Tool Use And Care; Specific Safety Rules For Water Pumps - Surtek BP505 Manual De Usuario

Before connecting the tool to a power source
(receptacle, outlet, etc.) be sure that the voltage
supplied is the same as that one specified on
the nameplate of the tool. To use a not specified
voltage may cause a serious injury to the user as
well as damage the tool.
IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.

TOOL USE AND CARE

Do not force the power tool. Use the correct
tool for the application. The correct tool will do
the job better and more safely at the rate that it
was designed to work at.
Do not use tools if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the plug from the power source be-
fore making any adjustments, changing acces-
sories or storing the tool. This preventive safety
measures reduce the risk of accidental starting
of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
E N G L I S H •
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
SERVICE: Tool service must be performed only
by qualified repair personnel. Service or main-
tenance performed by unqualified personnel
could result in a risk of injury.
SPECIFIC SAFETY RULES FOR
WATER PUMPS
· This pump is designed for pumping clean
neutral liquids, at temperatures not exceeding
35° C. Useful for irrigation of orchards and to
increase insufficient pressure of the water sup-
ply network.
WARNING: The water pump must not be
used when people or animals are in the water
· It must not be used for the drinking water sup-
ply or for the delivery of foodstuffs.
· Explosive, flammable, aggressive or health-
hazardous substances and faecal matter must
not be pumped.
· This product must not be exposed to dripping
or splashing liquids.
· The appliance is not suitable for continuous
running (e.g. permanent circulation in filter
systems).
· It is also not suitable for use with liquids con-
taining abrasive materials (e.g. sand) or contain-
ing mixtures of dirt, sand, mud or clay.
· Any other use is considered improper. Unpre-
dictable damage can occur as a result of improp-
er use, modifications to the appliance or due to
the use of parts which have not been tested and
approved by the manufacturer.
· The connection must be made to earthed sock-
ets which have been properly installed, earthed
and tested. Mains voltage and fuse must comply
with the technical data.
· Do not kink, crush, drag or drive over the mains
cable; protect against sharp edges, oil and heat.
· During operation for swimming pools, garden
ponds and similar places, the appliance must be
equipped with a residual current circuit breaker
(RCCB) with a design fault current of not more
than 30 mA.
· Disconnect the mains plug before all work on
the appliance .
· Do not install and switch on the appliance if
there are people or animals in the medium be-
ing pumped, or they are in contact with it.
· If repairs are carried out incorrectly, there is a
danger of liquid penetrating into the electrical
components of the appliance.
Us er's Manual
11