Optional Accessories - Makita UB1102 Manual De Instrucciones

A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclockwise
for lower speed.
OPERATION
CAUTION:
• Always hold the tool only by the handle when
performing an operation. Do not touch the metal part.
• Do not use the tool for blowing air into objects, like
rubber rafting, balls or other inflatable products.
Increased motor revolution may cause dangerous fan
breakage. (Fig. 3)
Blowing (Fig. 4)
For dust blowing, attach nozzle to blower outlet. Turn it
clockwise until it clicks.
Dust suction (optional accessory) (Fig. 5 & 6)
For dust suction, fit nozzle onto suction inlet and dust
bag onto blower outlet. Turn them clockwise until it clicks.
After the bag fills with dust, empty the contents of the
dust bag into a dust bin by releasing the fastener.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes (Fig. 7 & 8)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Joint
• Nozzle assembly
• Dust bag assembly
• Flexible hose
• Nozzle assembly (Long size)
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
4
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: operation without load
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Blower
Model No./ Type: UB1102, UB1103
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN60745
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
): 83 dB (A)
pA
): 94 dB (A)
WA
2
): 2.5 m/s
h
2
1.8.2014
Director
ENG905-1
ENG900-1
ENG901-1
ENH101-18